Plasma nitriding has become a powerful tool to improve wear resistance of stainless steels and sustain or improve corrosion resistance with an adequate selection of process parameters. In this work, the short treatment route with temperatures above 400ºC was selected for AISI 420 stainless steel. After the nitriding process, a wide nitrided layer, with good wear and corrosion properties was simultaneously obtained with selected parameters. A 5 hours treatment at 420 ºC resulted in a 10 µm nitrided layer. XRD revealed an expanded Fe-α layer with Fe nitrides but no signal of CrN was found. Wear resistance was improved three and four times in erosion and sliding tests compared to the non-nitrided material. Corrosion resistance was tested in anodic polarization experiments in a NaCl solution. In this test, the samples treated in the short time process presented the best results.
25 February 2019 in Journal of Bio- and Tribo-Corrosion
The austenitic stainless steel AISI 316L is used in chemical and other industries due to its good corrosion properties; however, it has a poor wear resistance. Plasma assisted treatments such as diffusion process and/or coatings can be used in order to improve the tribological properties. The a:C-H-Si coatings have low friction coefficient and wear resistance; in addition, they are chemically inert although they present adhesion problems when they are deposited on metallic substrates. In this work, the mechanical behavior and adhesion of the a:C-H-Si coatings deposited on nitrided AISI 316L stainless steel (duplex sample) and without nitriding (coated sample) were studied. The coatings were characterized by EDS and Raman. The hardness and Young Modulus were assessed with nanoindentation. The microstructure of the nitrided layer and the coatings was analysed by OM, SEM-FIB and XRD. Pin on disk and linear sliding tests were carried out. The adhesion was evaluated using Indentation Rockwell C and Scratch test. The coatings had high hydrogen content, over 40%, and the film thickness was about 20 μm. The hardness was about 13 GPa and Young's Modulus was 73 GPa. The friction coefficient was less than 0.2 and the wear resistance was better than in stainless steel without any treatment. In the linear sliding tests, the track depth in the duplex and coated samples was six times lower than in the untreated sample. The nitriding had influence on the adhesion; the critical load was 16.2 N in the duplex sample and of 9.6 N in the coated sample. In the indentation Rockwell C test, the duplex sample also had better adhesion than the only coated sample.
26 August 2022 in Surface Topography: Metrology and Properties
Martensitic stainless steels are often used in machine components, where are exposed to different solicitations that require good surface properties. Different treatments such as plasma nitriding or coating deposition could be used to improve their wear and corrosion resistance, even combining both methods. In this work, the tribological behaviour of a TiAlN coating with a top layer of TiN, called ‘Hyperlox Gold’, deposited over both nitrided and non-nitrided martensitic stainless steels by PVD PEMS (Physical Vapour Deposition Plasma Enhanced Magnetron Sputtering) was studied. Quenched and tempered AISI 420 martensitic stainless steel was used as base material. A group of samples were plasma nitrided and were subsequently coated. Microstructure of the nitrided layer and the coating were analysed by SEM and XRD. Nanohardness was measured with a Berkovich tip. Wear behaviour was evaluated using pin-on-disk tests (ASTM G99 standard) under three different loads (5 N, 7 N and 10 N) with an alumina ball as a counterpart. Adhesion was evaluated using dynamic conditions such as variable load scratch test and under static condition with Rockwell indentation tests (using 60 kg, 100 kg, and 150 kg). Overall thickness of the coatings was 3.7 μm and their hardness about of 32 ± 2 GPa. The nitrided layer was about 10 μm thick, with a hardness of 17 ± 1 GPa. The coating had good mechanical resistance in sliding adhesive wear conditions under low loads and good adhesion was revealed in a static condition. The presence of a nitrided layer improved the wear behaviour under high loads and the adhesion in dynamic conditions. Critical load was higher for the duplex sample than the coated samples. This work is important for the development of the Argentinian industry where the use of coatings is not largely extended, especially with martensitic stainless steels as substrates.