Leif  Karlsson

Prof. Leif Karlsson

orcid

Research Focus & Metrics

Academic Career Length

31Years (1996-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2018 in Materials
Verified
Journal Article
Open access
PDF file
VHVahid Hosseini
Vahid Hosseini
LKLeif Karlsson
Leif Karlsson
SWSten Wessman
Sten Wessman
NFNuria Fuertes
Nuria Fuertes
Sigma phase is commonly considered to be the most deleterious secondary phase precipitating in duplex stainless steels, as it results in an extreme reduction of corrosion resistance and toughness. Previous studies have mainly focused on the kinetics of sigma phase precipitation and influences on properties and only a few works have studied the morphology of sigma phase and its influences on material properties. Therefore, the influence of sigma phase morphology on the degradation of corrosion resistance and mechanical properties of 2507 super duplex stainless steel (SDSS) was studied after 10 h of arc heat treatment using optical and scanning electron microscopy, electron backscattered diffraction analysis, corrosion testing, and thermodynamic calculations. A stationary arc was applied on the 2507 SDSS disc mounted on a water-cooled chamber, producing a steady-state temperature gradient covering the entire temperature range from room temperature to the melting point. Sigma phase was the major intermetallic precipitating between 630 °C and 1010 °C and its morphology changed from blocky to fine coral-shaped with decreasing aging temperature. At the same time, the average thickness of the precipitates decreased from 2.9 µm to 0.5 µm. The chemical composition of sigma was similar to that predicted by thermodynamic calculations when formed at 800–900 °C, but deviated at higher and lower temperatures. The formation of blocky sigma phase introduced local strain in the bulk of the primary austenite grains. However, the local strain was most pronounced in the secondary austenite grains next to the coral-shaped sigma phase precipitating at lower temperatures. Microstructures with blocky and coral-shaped sigma phase particles were prone to develop microscale cracks and local corrosion, respectively. Local corrosion occurred primarily in ferrite and in secondary austenite, which was predicted by thermodynamic calculations to have a low pitting resistance equivalent. To conclude, the influence of sigma phase morphology on the degradation of properties was summarized in two diagrams as functions of the level of static load and the severity of the corrosive environment.

1 August 2015 in International Journal of Fatigue
Verified
Journal Article
Closed access
EHEbrahim Harati
Ebrahim Harati
LKLeif Karlsson
Leif Karlsson
LSLars-Erik Svensson
Lars-Erik Svensson
KDKamellia Dalaei
Kamellia Dalaei

1 February 2016 in Welding in the World
Verified
Journal Article
Closed access
PDF file
VHVahid Hosseini
Vahid Hosseini
MBMaria Asuncion Valiente Bermejo
Maria Asuncion Valiente Bermejo
JGJohannes Gårdstam
Johannes Gårdstam
KHKjell Hurtig
Kjell Hurtig
LKLeif Karlsson
Leif Karlsson

1 November 2021 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
ABAmir Baghdadchi
Amir Baghdadchi
VHVahid A. Hosseini
Vahid A. Hosseini
LKLeif Karlsson
Leif Karlsson

1 April 2017 in International Journal of Fatigue
Verified
Journal Article
Closed access
EHEbrahim Harati
Ebrahim Harati
LKLeif Karlsson
Leif Karlsson
LSLars-Erik Svensson
Lars-Erik Svensson
KDKamellia Dalaei
Kamellia Dalaei

1 November 2016 in International Journal of Fatigue
Verified
Journal Article
Closed access
EHEbrahim Harati
Ebrahim Harati
LSLars-Erik Svensson
Lars-Erik Svensson
LKLeif Karlsson
Leif Karlsson
MWMattias Widmark
Mattias Widmark