Ebrahim Harati

Dr. Ebrahim Harati

orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2015 in International Journal of Fatigue
Verified
Journal Article
Closed access
EHEbrahim Harati
Ebrahim Harati
LKLeif Karlsson
Leif Karlsson
LSLars-Erik Svensson
Lars-Erik Svensson
KDKamellia Dalaei
Kamellia Dalaei

1 March 2011 in Materials & Design (1980-2015)
Verified
Journal Article
Closed access
RJR. Arabi Jeshvaghani
R. Arabi Jeshvaghani
EHEbrahim Harati
Ebrahim Harati
MSM. Shamanian
M. Shamanian

1 November 2016 in International Journal of Fatigue
Verified
Journal Article
Closed access
EHEbrahim Harati
Ebrahim Harati
LSLars-Erik Svensson
Lars-Erik Svensson
LKLeif Karlsson
Leif Karlsson
MWMattias Widmark
Mattias Widmark

29 May 2017 in Materials
Verified
Journal Article
Open access
PDF file
EHEbrahim Harati
Ebrahim Harati
LKLeif Karlsson
Leif Karlsson
Lars-Erik SvenssonLars-Erik Svensson
Lars-Erik Svensson
TPThilo Pirling
Thilo Pirling
KDKamellia Dalaei
Kamellia Dalaei
Evaluation of residual stress in the weld toe region is of critical importance. In this paper, the residual stress distribution both near the surface and in depth around the weld toe was investigated using neutron diffraction, complemented with X-ray diffraction. Measurements were done on a 1300 MPa yield strength steel welded using a Low Transformation Temperature (LTT) consumable. Near surface residual stresses, as close as 39 µm below the surface, were measured using neutron diffraction and evaluated by applying a near surface data correction technique. Very steep surface stress gradients within 0.5 mm of the surface were found both at the weld toe and 2 mm into the heat affected zone (HAZ). Neutron results showed that the LTT consumable was capable of inducing near surface compressive residual stresses in all directions at the weld toe. It is concluded that there are very steep stress gradients both transverse to the weld toe line and in the depth direction, at the weld toe in LTT welds. Residual stress in the base material a few millimeters from the weld toe can be very different from the stress at the weld toe. Care must, therefore, be exercised when relating the residual stress to fatigue strength in LTT welds.

1 September 2017 in Engineering Failure Analysis
Verified
Journal Article
Closed access
EHEbrahim Harati
Ebrahim Harati
Lars-Erik SvenssonLars-Erik Svensson
Lars-Erik Svensson
LKLeif Karlsson
Leif Karlsson

12 May 2020 in Welding in the World
Verified
Journal Article
Open access
PDF file
EHEbrahim Harati
Ebrahim Harati
LSLars-Erik Svensson
Lars-Erik Svensson
LKLeif Karlsson
Leif Karlsson
In this paper, T-joint samples in a 1300 MPa yield strength steel were produced using conventional or low transformation temperature (LTT) type consumables. The welded samples were either subjected to high-frequency mechanical impact (HFMI) treatment or to shot-peening. Fatigue testing was performed under fully reversed, constant amplitude bending load. Shot-peening gave a significant increase in fatigue strength for more than around 50,000 cycles. Shot-peened LTT welds had the highest fatigue strength, with conventional welds being shot-peened having slightly lower fatigue strength. HFMI treatment of conventional and LTT welds improved the fatigue strength also, but to a lesser extent, keeping the slope in the SN diagram close to three, while shot-peened samples had a slope of 5–7. Significant differences in compressive residual stress were seen between the different welds, with the most compressive stress found in the shot-peened samples. This was probably one of the main reasons for the improved fatigue life of shot-peened samples.