This paper reviewed the research progress in China on the durability, acid and alkali corrosion resistances, thermal insulation, sound insulation, and hygroscopic properties of basalt fibers (BFs) as well as the physicochemical and mechanical properties of BF-reinforced resin composites. The acidity coefficient and pH value of BFs and glass fibers (GFs) were tested, which showed that BFs had better chemical stability. Scanning electron microscopy observations showed that the acid corrosion of BFs gradually occurred from the outside to the inside, whereas the alkali corrosion of BFs occurred nearly simultaneously both inside and outside. Moreover, the reasons for these results were analyzed from a chemical reaction perspective. BFs met the thermal conductivity and sound absorption coefficient requirements of building thermal insulation and sound absorption materials. The hygroscopicity of BFs was 1/8–1/6 that of GFs, and BFs also had a smaller dielectric loss angle. Tests confirmed that BFRC exhibited great high-temperature resistance. As the short BF content increased, the flexural strength, splitting tensile strength and impermeability of BFRC significantly improved, and an optimal fiber length and content were proposed. A comparison showed that the mechanical properties of BF-reinforced resin were generally better than those of GF-reinforced resin. Finally, this review identified some concepts to be studied in this field and prospects for possible future research directions. [ ]
1 December 2016 in Materials Science and Engineering: C
This paper reviews the pretreatment methods for wheat straw building materials and classifies the main methods according to their characteristics. The results indicate that the steam cooking and steam explosion treatment methods are relatively better than other methods and that particleboard and medium-density fiberboard manufactured using pretreated wheat straw possess correspondingly superior physical and mechanical properties. However, deficiencies in internal bonding, tensile strength, dimensional instability (swelling) and high moisture absorption remain. Thus, the present study proposes improving the pretreatment method and measurement and suggests a future development direction for the pretreatment of wheat straw building materials.
10 July 2017 in Journal of Sandwich Structures & Materials
To increase the engineering applications of basalt fiber, the characteristics of the shear mechanical properties and the influence mechanisms of the fiber length ( Lf) and volume fraction ( Vf) for short basalt fiber reinforced epoxy resin polymer composites were investigated. The following results were obtained: (1) The first critical loads on all the shear load–displacement curves are close to the same value due to having the same interface bonding of the fiber–matrix; (2) the shear strength, deformation, and energy dissipation capacity all increase with increasing Vf; however, when Lf is 6 or 9 mm, these increases are slower, whereas when Lf is 3 mm, these values increase at an approximately constant rate; and (3) the shear elastic modulus of the samples reaches its maximum value when Lf is 3 mm and Vf is 25%; however, it increases more quickly when Lf is 6 or 9 mm. The failure mode of the samples with the larger Lf values is mainly debonding between the fiber and matrix; when Vf is high, the fibers can easily bundle, which reduces the adhesion between the fibers and matrix. In addition, the main failure mode of the 3-mm-long fiber samples is fiber pull-out; when Vf is high, the short fibers that are not pulled out significantly increase the deformation ability.
5 January 2018 in Journal of Applied Polymer Science
To thoroughly study the stress–strain relationship of lightweight mixed ceramic concrete, this paper conducts axial compressive strength tests on three groups of lightweight mixed ceramic concrete specimens with different types and contents as the basis. It establishes the elastic modulus calculation formula and compressive stress–strain formula for lightweight mixed ceramic concrete by combining with the current standards and related research. The results show that lightweight mixed ceramic concrete, made of a mixture of different types and densities of ceramic grains, has better mechanical properties and deformation properties. The calculation errors of the modulus of elasticity formulas, derived from the experimental results for the three groups of lightweight mixed ceramic concretes, are all controlled within 5%. The average relative errors of the fitting results of stress–strain curves for the three groups of specimens and the measured data are as low as 6.66%, 3.16%, and 3.39%. The errors between the experimental values of the modulus of elasticity of different studies and the predicted values based on the formula in this paper were controlled within 17%, and the average relative errors between the predicted and experimental results of the stress–strain curves for the three groups of specimens were 2.64%, 8.94%, and 17.50%. This paper innovatively constructs a prediction model of key mechanical parameters of lightweight mixed ceramic concrete, which can provide a reference and experimental basis for the structural analysis and application of lightweight mixed ceramic concrete.