Baterai lithium-ion-polymer atau lithium-polymer merupakan salah satu jenis dari baterai berbasis lithium-ion. Saat ini, baterai berbasis Lithium-ion banyak digunakan pada berbagai macam perangkat portabel hingga kendaraan listrik. Pengisi daya atau charger untuk baterai berbasis Lithium-ion yang umum digunakan saat ini menggunakan metode constant current – constant voltage (CC-CV). Metode ini dianggap efektif untuk menghindari undercharging dan overcharging. Pada battery pack terdapat akumulasi resistansi yang dapat menyebabkan penurunan tegangan pada cell baterai, dan dapat mempercepat proses transisi dari mode CC menjadi mode CV. Percepatan transisi tersebut dapat mengakibatkan proses pengisian daya berlangsung lebih lama. Pada penelitian ini dibahas bagaimana proses kompensasi resistansi pada charger dengan topologi PLL, untuk mengompensasi akumulasi resistansi pada battery pack pada saat prosespengisian daya berlangsung. Pada simulasi didapatkan hasil bahwa pengisi daya dengan kompensasi resistansi menghasilkan waktu pengisian daya 17.82% lebih cepat, sedangkan pada uji coba alat didapatkan waktu pengisian daya 15.58% lebih cepat, kedua hasil tersebut jika dibandingkan dengan pengisi daya dengan topologi PLL tanpa kompensasi resistansi.
The aim of this research is to investigate the performance of indoor amorphous photovoltaic systems with PVC water cooling and compare them with those using heatsink cooling. The amorphous approach used in this study involves water flowing through a PVC pipe and a heatsink cooler. The circular heatsink that was used has fins all around it. The water flow through the pipe is pumped from the reservoir to the PVC pipe. The study found that a PVC water flow-based active cooling system is the most effective at preserving thermal stability and improving the performance of amorphous PV modules under high light intensity circumstances, providing insights for future advancements.
1 June 2026 in International Journal of Applied Power Engineering (IJAPE)
The implementation of micro-hydro power plants (MHPPs) offers a strategic solution for achieving energy independence, particularly within remote communities. This study proposes the development of a hydroelectric power generator with a vertical axis turbine, designed not only as a source of clean energy but also to minimize visual pollution. The system maximizes submerged components, thereby reducing its visual impact. Although MHPPs technology is widely applied to address electrification challenges in remote areas, the system proposed in this study, with its components predominantly submerged below the water surface, offers a visually unobtrusive solution that is also well-suited for urban environments. However, conventional locked-blade turbines often experience significant efficiency losses due to counter-flow pressure acting on blades moving against the water stream, highlighting the need for an adaptive mechanism to minimize drag and optimize energy capture. The hydroelectric power generator using vertical axis turbine with adaptive blades consistently demonstrated better performance than a system using locked blades. The adaptive-blade configuration outperformed the locked-blade system, exhibiting a 5.1% increase in average turbine efficiency and a 3.5% improvement in overall system efficiency.
5 June 2026 in Jurnal Pengabdian Masyarakat dan aplikasi Teknologi (Adipati)
Utilization of renewable energy sources is a necessity to reduce the consumption of fossil energy sources. On the end of 2021, it was reported that world was experiencing an energy crisis, so the use of renewable energy sources is being something urgent. Renewable energy power generation can be done in large scale to small scale even on household level. Electrical energy independence can be achieved, one way by utilizing available energy sources surrounding house. Several energy sources that can be utilized around the house including water, wind, sunlight, etc. Water as one of energy sources can also be obtained from the water flow in household plumbing systems. In this research, analysis of the output characteristics of generator was carried out from mini generator connected to screw turbine with in-pipe water flow as the energy source. Design and measurement have been done on the prototype to see the output characteristic of generator. Measurement on prototype have shown results to produce 1.56 watt and 9.6 volt at maximum water discharge 0.317 l/s, these results are quite low considering power measured at the turbine reaches about 7.45 watt. With further research, another more efficient and proper configuration can be obtained.