This study aimed to investigate the disintegration resistance of schist on the eastern slope of the Tongman open-pit mine. It examined the effects of cycle number and mineral composition on the disintegration resistance indexes of four types of schist through thin section identification and laboratory disintegration resistance tests. Furthermore, we analyzed the morphological characteristics of the disintegration residues using laboratory tests. Based on pore micro-damage theory, the mechanisms responsible for the differences in disintegration resistance among the four types of schist were further explored. The results show a negative correlation between the disintegration resistance index and the number of cycles. For the same number of cycles, the disintegration resistance indices for the four schist types were ranked as follows: greenish-gray chlorite-bearing muscovite schist > gray weakly chloritized biotite–muscovite schist > greenish-gray muscovite schist > gray muscovite schist. The disintegration residues of schist samples were categorized into four morphological patterns: thin sheet-like, moderately thick sheet-like, blocky, and granular. These patterns were then thoroughly elucidated. The differences in the disintegration resistance characteristics of schist were closely related to their material composition. The microstructural pore damage within the rock is the essential factor causing schist disintegration. Variations in rock porosity led to differing damage factors, which explain the distinct disintegration resistance characteristics observed across the four types of schist. The proposed preventive measures, developed through a systematic analysis of schist disintegration mechanisms, provide an effective framework for slope stability management. This research offers valuable insights into the weathering characteristics of rock masses in slope engineering, which is significant for understanding the progressive failure modes of disintegrating metamorphic formations.
1 July 2019 in IOP Conference Series: Earth and Environmental Science
In recent years, the shale gas development boom around the world has made finegrained sedimentary rocks become the focus and hotspot of sedimentological research. Lithofacies are rock types and assemblages formed in a certain sedimentary environment, and are important parameters in formation evaluation. The lithofacies classification of fine-grained sedimentary rocks is an important basis for the study of hydrocarbon source rocks, shale oil and gas and tight oil reservoirs. Anchored in the previous studies, the lithofacies classification scheme of fine grained sedimentary rocks in study area based on mineral composition was established in this paper. The results prove that the main lithofacies of Qiongzhusi formation in study area are mainly felsic clay rocks and clayey felsic fine-grained sedimentary rocks, and a small number of which are dolostone, limestone, felsic fine-grained sedimentary rocks, dolomitic felsic fine-grained sedimentary rocks, clayey felsic fine-grained sedimentary rocks, felsic dolostone, and dolomitic mixed fine-grained sedimentary rocks. This study can provide some geological basis for the evaluation and regional election of shale gas in this area.
Deep metal mines commonly contain vertically stacked goafs whose geometry and rock mass properties are incompletely documented. This study evaluates a field-constrained screening framework for high-displacement material scenarios at the Lehong Pb-Zn mine. The framework combines a Latin hypercube sampling (LHS)-FLAC3D response library with static Bayesian inference. Evidence comprised 93 goaf records, 186 Mathews exposed-surface assessments, laboratory constraints, and 40 archived numerical scenarios, whose maximum downward displacement ranged from 4.48 to 31.75 cm. Friction angle φ showed the strongest marginal Pearson correlation with displacement (r = −0.81), followed by cohesion (r = −0.55) and elastic modulus (r = −0.22). At the response library Q75 threshold of 15.04 cm, the Laplace-smoothed probability increased from 0.262 (95% credible interval, 0.142–0.403) across all scenarios to 0.600 (0.352–0.824) under joint cohesion–friction angle degradation. However, the archived design was not an ideal 40-point LHS, and bootstrap resampling retained the scenario ordering in only 45.8–54.8% of replicates. All 93 inventory identifiers matched the Mathews stability table, enabling reproducible site-level triage when Bayesian network results are combined with treatment and stability evidence. The framework is an exploratory screening tool rather than an absolute failure probability model, collapse propagation model, or dynamic early warning system.
1 February 2018 in IOP Conference Series: Earth and Environmental Science
The microscopic pore structure is the key of the shale reservoir study; however, traditional Scanning Electron Microscopy (SEM) methods cannot identify the irregular morphology caused by mechanical polishing. In this work, Scanning Electron Microscopy combined argon ion polishing technology was taken to study the characteristics of shale reservoir pores of Member 1 of Shahejie Formation (E3s1) located in JX1-1 area of Liaozhong Sag. The results show that pores between clay platelets, intraplatelet pores within clay aggregates and organic-matter pores are very rich in the area and with good pore connectivity, so these types of pores are of great significance for oil-gas exporation. Pores between clay platelets are formed by directional or semi-directional contact between edge and surface, edge and edge or surface and surface of laminated clay minerals, whose shapes are linear, mesh, and irregular with the size of 500 nm to 5 μm. The intraplatelet pores within clay aggregates are formed in the process of the transformation and compaction of clay minerals, whose shapes are usually linear with the width of 30 to 500 nm and the length of 2 to 50 μm. The organic-matter pores are from the process of the conversion from organic matters to the hydrocarbon under thermal evolution, whose shapes are gneissic, irregular, pitted and elliptical with the size of 100 nm to 2 μm. This study is of certain guiding significance to selecting target zones, evaluating resource potential and exploring & developing of shale gas in this region.