xiaodong wang

Dr. xiaodong wang


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 December 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
GCGuo ChenYang
Guo ChenYang
XWxiaodong wang
xiaodong wang
DHDexing He
Dexing He
JLJie Liu
Jie Liu
HLHongkun Li
Hongkun Li
YZYu Zhang
Yu Zhang
The safety and reliability of a ventilation system relies on an accurate friction resistance coefficient (α), but obtaining α requires a great deal of tedious measurement work in order to determine the result, and many erroneous data are obtained. Therefore, it is vital that α be obtained quickly and accurately for the ventilation system design. In this study, a passive and active support indicator system was constructed for the prediction of α. An RF model, GSCV-RF model and BP model were constructed using the RF algorithm, GSCV algorithm and BP neural network, respectively, for α prediction. In the GSCV-RF and BP models, 160 samples complied with the prediction indicator system and were used to construct a prediction dataset and, this dataset was divided into a training set and a test set. The prediction results were based on the quantitative evaluation models of MAE, RMSE and R2. The results show that, among the three models, the GSCV-RF model’s prediction result for α was the best, the RF model performed well and the BP model performed worst. In the prediction for all the datasets obtained by GSCV-RF model, all the values of MAE and RMSE were less than 0.5, the values of R2 were more than 0.85 and the value of R2 of the passive and active support test sets were 0.8845 and 0.9294, respectively. This proved that the GSCV-RF model can offer a more accurate α and aid in the reasonable design and the safe operation of a ventilation system.

20 January 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
DHDexing He
Dexing He
XWxiaodong wang
xiaodong wang
GCGuo ChenYang
Guo ChenYang
HLHongkun Li
Hongkun Li
YZYu Zhang
Yu Zhang
The main intake shaft in the mine serves as the main intake and return air shaft and also serves as a lifting shaft. The piston wind effect caused by the frequent operation of large and efficient hoisting cages in the shaft will disturb the normal flow of airflow in the transport lane connected to the shaft and affect the underground ventilation effect. Therefore, based on the SST k-ω turbulence model, this paper uses the dynamic mesh to simulate the air-fluid in the cage running in the shaft and verifies the simulation data through field measurement to study the influence of piston effect on the airflow field in the transport lane. The results show that the piston effect caused by cage operation in the shaft will disturb the flow of normal airflow in the transportation lane and affect the ventilation effect in the mine. The 1765.0 m transport lane is closest to the position of the shaft inlet, which is most significantly affected by the piston wind effect. The low-speed eddy current zone generated at the tail of the cage in the upwind operation has a large area and strong adsorption force, which causes the gas at the local position in the transportation lane to generate eddy current and reverse flow, hindering the flow of fresh air in the lane. The influence distance and strength of the piston effect on each measuring point in the transportation lane are limited. When the measuring point distance increases from 21.7 m to 71.7 m, the differential pressure of measuring points in 1414.0 m, 1584.0 m and 1765.0 m transport lanes decreases by 11.08 Pa, 9.62 Pa and 8.58 Pa, respectively.

22 October 2026 in Eng
Verified
Journal Article
Open access
PDF file
ZZZhangrui Zhang
Zhangrui Zhang
JDJun Du
Jun Du
LLLiu Lei
Liu Lei
XWxiaodong wang
xiaodong wang
To investigate scale effects on the shear strength and mesoscale load-bearing structure of coarse-grained soil, four specimen groups with maximum particle sizes of 10, 20, 40, and 60 mm were tested in large-scale direct-shear tests under normal stresses of 100–400 kPa. Corresponding three-dimensional PFC3D discrete element models were established and assessed against the shear stress–displacement curves and strength parameters. Particle displacement, contact force chains, coordination number, contact fabric, and the shear stress field were then examined. The simulations agreed reasonably well with the laboratory tests: the mean relative error across 16 peak shear-stress comparisons was 4.09%, and the maximum error was 7.27%. At a given normal stress, peak shear stress increased with maximum particle size. As the maximum particle size increased from 10 to 60 mm, peak shear stress increased by 61.82% and 39.23% under normal stresses of 100 and 400 kPa, respectively; apparent cohesion increased from 6.8 to 25.5 kPa, and the internal friction angle φ increased from 26.8° to 33.9°. The total number of contacts decreased from 60,740 to 8537 and the coordination number from 4.951 to 2.564, whereas the strong-contact load-bearing proportion increased from 71.36% to 82.93%. Thus, the increase in shear strength was associated with load concentration on a smaller number of strong contacts rather than an increase in contact number. Specimens with larger particles developed more prominent strong force chains and clearer inclined load-transfer paths. Their contact fabric became increasingly directional, while the shear stress field changed from a relatively smooth banded pattern to localized patches. The preferred orientations of the strong force chains, contact fabric, and stress field were broadly consistent. Under an equivalent gradation area, increasing the maximum particle size strengthened interlocking among coarse particles and reorganized the load-bearing network from distributed transfer through many contacts to concentrated transfer through fewer strong contacts, thereby increasing the shear strength.

22 May 2026 in Sensors
Verified
Journal Article
Open access
PDF file
ZLZhuoqing Li
Zhuoqing Li
JHJie Hou
Jie Hou
LHLongqiang Han
Longqiang Han
XWxiaodong wang
xiaodong wang
Coal spontaneous combustion in gob areas is a major disaster endangering safe production in underground coal mines, and accurate prediction of carbon monoxide (CO), the core signature gas of coal oxidation, is critical for early warning and targeted prevention of mine fire disasters. However, CO concentration in gob areas is governed by complex gas–solid thermal–chemical multi-field coupling, presenting strong nonlinear characteristics. Traditional numerical methods suffer from prohibitive computational cost, purely data-driven models have inherent black-box defects, and conventional Physics-Informed Neural Networks (PINNs) require explicit full governing equations, which are hard to establish for such complex systems. This paper first proposes a Physics-Informed Modified Kolmogorov–Arnold Network (PIM-KAN), which deeply integrates domain physical knowledge with KAN architecture via a physics encoding layer, a residual-modified KAN layer, a multi-physics attention mechanism, and a multi-term physical consistency constraint framework. Experiments on 3125 real coal mine field samples show that the PIM-KAN achieves R2 = 0.9965 and RMSE = 0.9290 ppm, reducing RMSE by 19.5% compared with MLP, and outperforming all baseline models. Ablation studies confirm the significant contribution of each innovation module, and attention weight analysis is highly consistent with Arrhenius reaction kinetics, verifying its superior prediction accuracy, physical consistency and intrinsic interpretability.

25 August 2026 in Mining
Verified
Journal Article
Open access
PDF file
SYShuo Yan
Shuo Yan
XWxiaodong wang
xiaodong wang
YWYiming Wen
Yiming Wen
XNXiangdong Niu
Xiangdong Niu
Yong ChengYong Cheng
Yong Cheng
Deep metal mines commonly contain vertically stacked goafs whose geometry and rock mass properties are incompletely documented. This study evaluates a field-constrained screening framework for high-displacement material scenarios at the Lehong Pb-Zn mine. The framework combines a Latin hypercube sampling (LHS)-FLAC3D response library with static Bayesian inference. Evidence comprised 93 goaf records, 186 Mathews exposed-surface assessments, laboratory constraints, and 40 archived numerical scenarios, whose maximum downward displacement ranged from 4.48 to 31.75 cm. Friction angle φ showed the strongest marginal Pearson correlation with displacement (r = −0.81), followed by cohesion (r = −0.55) and elastic modulus (r = −0.22). At the response library Q75 threshold of 15.04 cm, the Laplace-smoothed probability increased from 0.262 (95% credible interval, 0.142–0.403) across all scenarios to 0.600 (0.352–0.824) under joint cohesion–friction angle degradation. However, the archived design was not an ideal 40-point LHS, and bootstrap resampling retained the scenario ordering in only 45.8–54.8% of replicates. All 93 inventory identifiers matched the Mathews stability table, enabling reproducible site-level triage when Bayesian network results are combined with treatment and stability evidence. The framework is an exploratory screening tool rather than an absolute failure probability model, collapse propagation model, or dynamic early warning system.