Weiqun Yuan

Dr. Weiqun Yuan


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 April 2023 in IEEE Transactions on Plasma Science
Verified
Journal Article
Closed access
YCYunlong Che
Yunlong Che
WYWeiqun Yuan
Weiqun Yuan
WYWu Yuan
Wu Yuan
ZWZhizeng Wang
Zhizeng Wang
WHWei Hao
Wei Hao
PYPing Yan
Ping Yan
In previous studies, the armature–rail sliding contact interface is usually considered to be an ideal slide in which both rails are parallel and symmetric. However, due to the influence of structural deformation of the barrel affected by boundary constraints and the manufacturing errors of rails and armature, it often leads to a variety of nonideal the armature–rail matching such as space curved or twisted rails, offset or deflected armature, and so on. This article focuses on the common vertical curved rail in electromagnetic railgun. By introducing centrifugal force effects and coupling electromagnetic force, the armature–rail contact pressure is analyzed theoretically. According to the 3-D finite-element simulation results, the effect of centrifugal force on sliding contact pressure should not be ignored. The effects of different curved radii, velocities, and densities of armature on the contact pressure are compared and analyzed. The influence law on the contact pressure is obtained, which provides a theoretical basis for the design of the railgun.

14 June 2022 in IEEE Transactions on Plasma Science
Verified
Journal Article
Closed access
WTWen Tian
Wen Tian
WZWeikang Zhao
Weikang Zhao
GLGuochao Li
Guochao Li
CMChen Miao
Chen Miao
YZYing Zhao
Ying Zhao
PYPing Yan
Ping Yan
The sliding electrical contact (SEC) between rails and armature is a focus in electromagnetic rail launchers. The extreme conditions, such as high current density, high temperature, and high contact pressure, influence SEC performance. In this article, the segmented rails were used to study the effects of launch mass on SEC. Two groups of experiments, armatures with and without launch mass, were carried out. The mass difference of rail parts was measured, the macro-and micromorphology of rails surface were observed, and the driving current and muzzle voltage were obtained. Three conclusions are obtained: 1) the mass difference of rail parts in shooting with launch mass is greater than that without launch mass, due to the high temperature of armature contact surfaces; 2) because of the electron migration, the mass difference of the cathode rail is larger than the anode rail; and 3) the contact resistance between rails and armature without launch mass is lower than that with launch mass, result from the large contact area. Moreover, the current density and the temperature of the armature and rails were calculated. Results show that the temperature of surface of armature with launch mass is higher than that without launch mass. In a word, based on the results from experiments and simulations, the launch mass improves the sliding electric contact performance.

20 November 2017 in Measurement Science and Technology
Verified
Journal Article
Closed access
PDF file
WXWeidong Xu
Weidong Xu
WYWeiqun Yuan
Weiqun Yuan
RXRong Xu
Rong Xu
HZHui Zhao
Hui Zhao
WCWenping Cheng
Wenping Cheng
PYPing Yan
Ping Yan
This paper introduces a new measurement system for measuring the position of a projectile within a rapid fire electromagnetic launching system. The measurement system contains both non-contact laser shading and metal fiber contact measurement devices. Two projectiles are placed in the rapid fire electromagnetic launch bore, one in the main accelerating segment and the other in the pre-loading segment. The projectile placed in the main accelerating segment should be shot first, and then the other is loaded into the main segment from the pre-loading segment. The main driving current ( I - main ) can only be discharged again when the second projectile has arrived at the key position (the projectile position corresponds to the discharging time) in the main accelerating segment. So, it is important to be able to detect when the second projectile arrives at the key position in the main accelerating segment. The B-dot probe is the most widely used system for detecting the position of the projectile in the electromagnetic launch bore. However, the B-dot signal is affected by the driving current amplitude and the projectile velocity. There is no current in the main accelerating segment when the second projectile moves into this segment in rapid fire mode, so the B-dot signal for detecting the key position is invalid. Due to the presence of a high-intensity magnetic field, a high current, a high-temperature aluminum attachment, smoke and strong vibrations, it is very difficult to detect the projectile position in the bore accurately. So, other measurements need to be researched and developed in order to achieve high reliability. A measurement system based on a laser (non-contact) and metal fibers (contact) has been designed, and the integrated output signal based on this detector is described in the following paper.

16 May 2025 in Energies
Verified
Journal Article
Open access
PDF file
WTWen Tian
Wen Tian
GWGongwei Wang
Gongwei Wang
YZYing Zhao
Ying Zhao
WZWeikang Zhao
Weikang Zhao
WYWeiqun Yuan
Weiqun Yuan
PYPing Yan
Ping Yan
During the electromagnetic launching process, the actual current input into the launcher is obtained by controlling the discharge of the pulsed power supply. Generally, the waveform of the pulse current is determined by the discharge characteristics and discharge time of the pulse power supply. Due to the limitation of control accuracy, the driving current is not an ideal trapezoidal wave, but there is a certain fluctuation (current ripple) in the flat top portion of the trapezoidal wave. The fluctuation of the current will affect the thickness of the liquefied layer at the armature–rail interface as well as the magnitude of the contact pressure, thereby inducing instability at the armature–rail interface and generating micro-arcs, which result in a reduction in the service life of the rails within the launcher. Consequently, it is imperative to conduct an in-depth analysis of the influence of current ripple on the liquefied layer during electromagnetic launching. In this paper, a thermoelastic magnetohydrodynamic model is constructed by coupling temperature, stress, and electromagnetic fields, which are predicated on the Reynolds equation of the metal liquefied layer at the armature–rail contact interface. The effects of current fluctuations on the melting rate of the surface of the armature, the thickness of the liquefied layer, and the hydraulic pressure of the liquefied layer under four different current ripple coefficients (RCs) were analyzed. The results show the following: (1) The thickness and the pressure of the liquefied layer at the armature–rail interface fluctuate with the fluctuation of the current, and, the larger the ripple coefficient, the greater the fluctuations in the thickness and pressure of the liquefied layer. (2) The falling edge of the current fluctuation leads to a decrease in the hydraulic pressure of the liquefied layer, which results in the instability of the liquefied layer between the armature and rails. (3) As the ripple coefficient increases, the time taken for the liquefied layer to reach a stable state increases. In addition, a launching experiment was also conducted in this paper, and the results showed that, at the falling edge of the current fluctuation, the liquefied layer is unstable, and a phenomenon such as the ejection of molten armature and transition may occur. The results of the experiment and simulations mutually confirm that the impact of current fluctuations on the armature–rail interface increases with increases in the ripple coefficient.


6 January 2026
Verified
Book Chapter
Closed access
PDF file
RGRuijie Guo
Ruijie Guo
GWGongwei Wang
Gongwei Wang
WTWen Tian
Wen Tian
JYJin Yang
Jin Yang
WYWeiqun Yuan
Weiqun Yuan
PYPing Yan
Ping Yan