3D Printing adalah sebuah printing yang menampilkan data dalam bentuk cetakan, namun berbeda dengan printing biasanya yang mencetak data dalam sebuah kertas ataupun lembaran lainnya. Dengan teknologi dari 3D printing sebuah perusahaan dapat membuat sebuah prototype tanpa harus menghabiskan bahan baku ataupun material. Dalam penelitian ini, dikaji tentang pengaruh parameter temperatur nozzle dan base plate pada material PLA terhadap kehalusan permukaan. Pada proses penelitian ini material yang dipakai adalah Poly Lactid Acid (Poly Lactic Acid ) yang kemudian akan dibentuk menjadi spesimen dengan ukuran 30x30x10 mm. Dengan menggunakan temperatur nozzle yaitu 190°C, 205°C, 220°C dan temperatur base plate 30°C dan 50°C serta menggunakan lem dan tidak menggunakan lem. Pada penelitian ini, didapatkan hasil density yang paling mendekati dengan density material adalah pada temperatur nozzle 190°C dan temperatur base plate 50°C dengan menggunakan lem ataupun tidak pada single nozzle sebesar 1.734 g/cm3
The automotive technology race to improve the efficiency of engine performance is increasing, one of which is the use of heat energy in car radiators. This is in addition to reducing the workload of the engine. It can also produce electrical energy. This experiment uses four pieces of TEC1-12706 thermoelectric generators (TEG) which are arranged in series with heat sink construction in the direction of the fluid flow mounted directly above the TEG fixture. TEG Fixture will be installed on Lombardini diesel engine upper hose radiator LDW1404. This experiment produces a maximum voltage of 2.05 volts, with the current strength of 68.4 mA (0.064 A) and the power generated is 140.22 mA (0.14 A) with a difference in heat sink temperature from the heat side of 17, 8°C.
30 April 2020 in Simetris: Jurnal Teknik Mesin, Elektro dan Ilmu Komputer
Berdasarkan data dari Survey Industri BP Batam tahun 2017, peningkatan kapasitas produksi produk plastik semakin signifikan. Hal ini ditunjukkan dengan banyaknya perusahaan dari China yang datang ke Batam untuk mengembangkan usaha plastik mereka. PT. Schneider Electric Batam, salah satunya yang mengalami peningkatan kapasitas produksi. Return pin merupakan salah satu produk yang akan dikembangkan, melalui penambahan jumlah core dan cavity nya. Jenis bahan baku plastik yang digunakan, yaitu POM (Polyoxymethylene), serta Stavax ESR sebagai bahan baku mold insert yang digunakan. Penelitian ini bertujuan untuk peningkatan kapasitas produksi cetakan plastik, dengan usulan perancangan baru untuk merubah mold insert dan tetap mempertahankan mold based yang telah ada. Perancangan dilakukan dengan metode VDI (Verein Deutsche Inginieuer) 2222 yang merupakan standar perancangan dalam membuat desain Mold. Software CAD yang digunakan adalah Siemens NX 9.0 dan Software CAE yang digunakan adalah Moldex 3D Flow Mold. Dari perancangan ini, didapatkan hasil cycle-time sebesar 11.5 detik dengan penghematan anggaran sebesar 46.7%.
The research aims to analyze the effect of metering stroke on product quality. Metering strokes relate to product weight and mold capacity. The material used is Polyamide (Nylon) 66, using an ENGEL 50ton capacity Injection Molding machine. The research method used is an experimental method before mass pre-production with stroke metering variation as a production parameter. A normality test was used to investigate the experimental data. Shapiro-Wilk's formula on Minitab® software was used to process the data. Product defects caused by an improper metering stroke often in the injection process are short mold and flashing prints. The results show that short mold production defects occur when the metering stroke is 60 mm due to the material does not fill the full cavity. Furthermore, flashing occurs when the metering stroke is 70 mm due to out of cavity capacity. Therefore, the appropriate parameter is a 65 mm metering stroke with good quality part results.
31 December 2020 in Jurnal Teknologi dan Riset Terapan (JATRA)
This study aims to determine the direction of development in the world of Mold & Dies design in the world. Data searches were carried out through science direct databases using the design of molds and dies as keywords with a limitation of open access journals between 2015 - 2020. The results were comprehensively analyzed based on year, publisher's name, institution, and the country as well as research subjects. Files from Mendeley software are saved in Reference Manager Format (.RIS) format which is processed into VOSviewer software to find out the bibliometric map. The results revealed that the highest number of publications is in a procedia manufacturing journal. The most contributing country in the European continent indexed in Scopus is Germany. Within the output in the form of network visualization, it is found that several novelty potentials are in line with the direction of the development of the study with the parameters of the number of population and the year of the research output. Publications on the most similarity and chance of novelty on research topics are in Cluster 1, which consists of Energy Efficiency, Decision Process, Plastic Materials, and Sustainability. Keywords: Novelty, Injection Mold Design, Bibliometric Maping, VOSviewer
30 June 2021 in Jurnal Teknologi dan Riset Terapan (JATRA)
Computer-Aided Design (CAD) and Computer-Aided Manufacturing (CAM) are usually used to draw sketches and model manufacturing work processes on machines that operate using computer numerical control (CNC). To communicate with each other CAD and CAM must have the same format, the drawings produced by CAD must the same format to be run on the CAM. In this study, product images will be created using Autocad software and it will run on the Fikus VisualCAM 19 software to visualize the tool pathway. The program is created to run a CNC machine and the resulting product will check the conformity of its dimensions and geometry. The results obtained are that the images generated from the AutoCAD software can run well on the Fikus VisualCAM 19 software. The program in the form of NC code generated by AutoCAD and Fikus VisualCAM19 software can be run properly by a CNC wire-cutting EDM machine, this can be seen from the product results that match the dimensions and geometry.