Journal bearings are critical components designed to facilitate the smooth and consistent rotation of shafts around specific axes. To meet the demands for efficient and cost-effective applications in high-speed machinery, it is imperative to enhance the tribological performance of journal bearings. This study investigates the impact of multistep texture geometry and partial surface roughness on the tribological behavior of journal bearings fabricated from steel. Experimental analyses were performed using Newtonian fluids across varying rotational speeds to evaluate the interplay between geometry and material properties. To further explore these dynamics, a three-dimensional computational fluid dynamics (CFD) model integrated with fluid–structure interaction (FSI) was employed, accounting for the effects of cavitation and material deformation under elastohydrodynamic lubrication conditions. The study also introduced partially rough surface boundary conditions to the multistep journal bearings, hypothesizing their potential to enhance lubrication performance. Results demonstrate that surface texture and roughness significantly influence the elastohydrodynamic lubrication and overall tribological performance of steel journal bearings. Additionally, variations in rotational speed were found to have a pronounced effect on lubrication efficiency. These findings provide valuable insights into optimizing journal bearing design for high-performance applications.
1 May 2019 in Journal of Physics: Conference Series
Activated carbon is one of the basic needs in food processing. Activated carbon can be improved from rock, wood and bone processing. This study aims to determine the quality of activated carbon pyrolysis processing from various woods using high temperatures ranging from 500-750 °C. The wood to be made into activated carbon is teak, mango, and jackfruit. Where teak, mango, and jackfruit are the types of wood used for fuel in industrial tofu boilers. The results of this combustion usually only become waste as charcoal boiler waste. The results of combustion contain carbon which can be used as this activated carbon. The quality of activated carbon is seen from the quality test based on SII and SNI. The results of the tests carried out that the best quality activated carbon is activated carbon which is activated by using heat at a temperature of 750 °C with a water test value of 1.01%, evaporator 15.12%, 2.3 ash, carbon-bound 82, 5%, iodine uptake rate 314.15 mg/gram, crystalline rate 40.886% with XRD analysis, pore diameter 8,72 μm, and chemical composition (% b) 95.94% C, 0.33% SO3, 2.06 % chloride, 0.49% K2O, 0.79% Calcium oxide, and 0.38% Cuprum oxide using SEM-EDX.
Pengelasan merupakan metode penyambungan yang umum digunakan dalam bidang konstruksi maupun aplikasi di industri. Tujuan dari penelitian ini adalah untuk mengetahui karakteristik sifat fisik dari pengamatan struktur makro, mikro serta karakteristik mekanik dari pengujian tarik. Parameter pengelasan perlu diketahui karena berpengaruh dengan sifat mekanik material setelah dilakukan pengelasan. Pada penelitian ini proses pengelasan yang digunakan adalah GTAW atau TIG dengan gas Argon. Penelitian ini menggunakan variasi arus 60 A, 70 A, 80 A. Berdasarkan hasil pengujian spesimen dengan arus 80 A memiliki tegangan tarik maksimal tertinggi 744,162 MPa. tegangan tarik terendah pada arus 70 A dengan nilai 598,435 MPa. Dan regangan tertinggi 82 % pada arus 80 A Hubungan antara kekuatan tarik dan struktur mikro semakin besar butiran logam yang dihasilkan maka tegangan luluhnya semakin kecil. Karena panas yang dihasilkan tidak cukup membuat elektroda tungsten dan bahan tambahnya meleleh dengan baik.Kata kunci: stainless steel, GTAW, kuat arus, kekuatan tarik.
Cast iron is widely used due to low price, good machining and good damping capability. However, it has huge friction. In certain automotive components such as cylindrical liner, cast iron is used. The biggest challenge in cylinder liner is obtaining lower friction and wear. The main aim of the paper is to experimentally investigate...
30 October 2024 in Al Ibtida: Jurnal Pendidikan Guru MI