International audienceThis paper introduces a modified enhanced transmission-line theory to account for higher-order modes while using a standard transmission line equation solver or equivalently a Baum, Liu and Tesche (BLT) equation solver. The complex per-unit-length parameters as defined by Nitsch et al. are first cast into an appropriate per-unit-length resistance, inductance, capacitance and conductance (RLCG) form. Besides, these per-unit-length parameters are modified to account for radiation losses with reasonable approximations. This modification is introduced by an additional per-unit-length resistance. The reason and explanations for this parameter are provided. Results obtained with this new formalism are comparable to those obtained using an electromagnetic full-wave solver, thus extending the capability of conventional transmission line solvers
27 May 2021 in IEEE Transactions on Electromagnetic Compatibility
Radio performance is very important in the automotive industry. It is necessary to provide a careful assessment of radio reception of each vehicle project development. It is well known that the vehicle radio performance may be affected by electromagnetic interferences from the components of the vehicle itself. These interferences degrade the radio signals and prevent the on-board receiver from retrieving correctly the baseband signal. Generally, the car manufacturers rely on the international special committee on radio interference (CISPR) 25 standard to decide whether radio reception tests pass or fail according to the interference limits set in advance. However, although the standard is able to detect interferences and determine their type and level according to various detectors, their consequence on radio reception quality (if any) cannot be assessed in a quantitative manner. This is even more difficult with digital communication systems such as digital analog broadcasting (DAB). For the time being, the final quality of the radio reception is evaluated in a totally independent way, through driving tests. This article introduces an improved test setup that performs both interference level measurements and assessment of the radio reception performance. Two operating modes are described. They are based either on the conducted or the radiated injection of the transmitted radio signal. Although dedicated to analog and digital transmissions, we will deal only with the analog radio (FM) in this article. From a set of experiments, we conclude that interferences measured with average detectors are more likely correlated to radio reception issues.
13 January 2020 in IEEE Transactions on Electromagnetic Compatibility
This article presents a global methodology to test components (equipment) on table test bench with representative interferences found on vehicle simulation in case of wideband modulated pulse interferences. The proposed method consists, first, of using an electromagnetic three-dimensional simulation model of the vehicle already validated to quickly determine time-domain waveforms of the common-mode current at any load connected at the end of a copper wire located inside the vehicle under wideband modulated pulse interferences. The second step of the method consists of showing that representative interference waveforms obtained by simulation can be reinjected into a component under test using conducted injection means usually used for electromagnetic compatibility tests in automotive industry in order to cover vehicle tests in case of Wideband/Mesoband modulated pulse interferences.
7 April 2026 in IEEE Transactions on Electromagnetic Compatibility
Dynamic wireless power transfer systems for electric vehicles rely on magnetic field coupling between a roadway-embedded transmitter (Tx) and a vehicle-mounted receiver (Rx). While enabling efficient energy transfer, the radiated magnetic field raise concerns related to electromagnetic field (EMF) exposure and electromagnetic interference, particularly with implantable medical devices. Existing mitigation approaches such as conductive shields, magnetic materials, and passive reactive loops are limited by tradeoffs involving efficiency loss, added mass, cost, or insufficient control. This article presents a comprehensive methodology for active magnetic field compensation, based on a machine learning-assisted optimization of the electrogeometrical configuration of an additional compensation (or shielding) coil, connected in series with the Tx coil. The surrogate model guides the design to minimize leaked magnetic flux density in critical exposure zones while preserving power transfer efficiency above 90% under nominal load. Simulation results reveal that the proposed solution reduces peak flux density by up to 70% with a negligible efficiency penalty. The approach is validated through three-dimensional finite-element analysis and experimental prototypes.
26 October 2023 in IEEE Transactions on Electromagnetic Compatibility
The purpose of this article is to present a new method for measuring the shielding effectiveness (SE) of enclosures without the use of an internal sensor. This technique uses a reverberation chamber (RC) and relies on the ability to accurately estimate the Q -factor as a function of frequency under different load conditions using an electromagnetic absorbing material. This material is placed successively in the RC, outside and inside the shielded enclosure under test (EUT). Based on the contrast of the Q -factor estimates, it is possible, in a noninvasive way, to characterize the SE of the EUT, using an energy conservation approach. The dynamic range of measurements is assessed. Experimental results are provided. It validates the principle and confirms the estimated dynamic range.
In order to reduce the radiated emissions due to high power converters in electric and hybrid vehicles, shielded cables are systematically used. This paper presents measurement results of the common-mode current and the radiated magnetic field produced by a shielded cable when different car body materials are considered. A simple but sufficiently representative measurement setup has been defined and constructed to take into account the impact of the new materials considered in automotive industry, such as low conductive carbon fiber reinforced epoxy. The results obtained allow evaluating the magnetic field produced between 10 kHz and 10 MHz when the shielded cable is either inside or outside the car body.