Damian Nabel

Mr. Damian Nabel

orcid

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 March 2025 in Materials
Verified
Journal Article
Open access
PDF file
Grażyna Mrówka-NowotnikGrażyna Mrówka-Nowotnik
Grażyna Mrówka-Nowotnik
GBGrzegorz Boczkal
Grzegorz Boczkal
DNDamian Nabel
Damian Nabel
This study investigated the effect of the recycling process on the microstructure, hardness, and precipitation kinetics of strengthening phases in the 2017A aluminum alloy. Light microscopy (LM) and X-ray diffraction (XRD) analyses revealed that the as-cast microstructure of the recycled 2017A alloy contained intermetallic phases, including θ-Al2Cu, β-Mg2Si, Al7Cu2Fe, Q-Al4Cu2Mg8Si7, and α-Al15(FeMn)3(SiCu)2, and was comparable to that of the primary alloy, confirming its potential for high-performance applications. During solution heat treatment, most of the primary intermetallic precipitates, such as Al2Cu, Mg2Si, and Q-Al4Cu2Mg8Si7, dissolved into the solid Al matrix. DSC analysis of the solution-treated alloy established the precipitation sequence as follows: α-ss → GP/GPB zones → θ″ → θ′/Q′ → θ-Al2Cu/Q-Al4Cu2Mg8Si7. The combined results from XRD, LM, TEM, and DSC confirmed that both θ and Q phases contributed to strengthening, with θ″ and θ′ phases playing a dominant role. Brinell hardness measurements during natural and artificial aging revealed that hardness increased with aging time, reaching a maximum value of 150.5 HB after ~22 h of artificial aging at 175 °C. The precipitation kinetics of the recycled 2017A alloy was studied via DSC measurements over a temperature range of ~25 to 550 °C, at heating rates of 5, 10, 15, 20, and 25 °C/min. The peak temperatures of clusters, GP zones, and hardening phases (θ′, θ″, θ, and Q) were analyzed to calculate the activation energy using mathematical models (Kissinger, Ozawa, and Boswell). The obtained values of activation energies of discontinuous precipitation were comparable across methods, with values for the θ″ phase of 89.94 kJ·mol−1 (Kissinger), 98.7 kJ·mol−1 (Ozawa), and 94.33 kJ·mol−1 (Boswell), while for the θ′ phase, they were 72.5 kJ·mol−1 (Kissinger), 81.9 kJ·mol−1 (Ozawa), and 77.2 kJ·mol−1 (Boswell). These findings highlighted the feasibility of using recycled 2017A aluminum alloy for structural applications requiring high strength and durability.

6 February 2025 in Preprints.org
Verified
Preprint
Open access
PDF file
Grażyna Mrówka-NowotnikGrażyna Mrówka-Nowotnik
Grażyna Mrówka-Nowotnik
GBGrzegorz Boczkal
Grzegorz Boczkal
DNDamian Nabel
Damian Nabel
Kinetic parameters that describe phase transformation and precipitation rates include the activation energy. In Al based alloys, volume fractions of precipitates, the melting temperature of specific phases and the activation energy of reactions can, in most cases, be determined by the differential scanning calorimetry (DSC) technique. In this investigation, DSC measurments were performed on a SETARAM SETSYS Evolution-1200 thermal analyzer on recycled aluminium alloy 2017A in the range of temperature from room ~25 to 700°C and different scan rates of heating at 5,10,15, 20 and 25°C min-1. The peak temperatures of the clusters, GP zones and hardening phases ’"and  Q from each heating rate were collected to calculate the activation energy associated with precipitation reactions in aluminium alloy 2017A using various mathematical models: the Kissinger, Ozawa and Boswell. The results (XRD, LM, TEM, DSC) show that both the θ and Q phases are strengthening phases, but the strengthening effect of the ",  phases is dominant. The strengthening phases, mainly ", ' increase the hardness during natural aging. The maximum hardness value 128HB was obtained after ~25h of natural ageing. The activation energy of precipitation of strengthening phase θ” in 2017A aluminum alloy determined by Kissinger, Ozawa and Boswell models are: 89.94 kJ· mol−1, 98.7 kJ· mol−1 and 94.33 kJ· mol−1 respectively and for θ’: 72.5 kJ· mol−1, 81.9 kJ· mol−1 and 77.2 kJ· mol−1 .

1 January 2025 in Advances in Mechanical and Materials Engineering
Verified
Journal Article
Open access
PDF file
PKPatryk Kamuda
Patryk Kamuda
Marek GoralMarek Goral
Marek Goral
KOKamil Ochał
Kamil Ochał
DNDamian Nabel
Damian Nabel
TKTadeusz Kubaszek
Tadeusz Kubaszek
Thermal spraying is playing an increasingly important role among coating manufacturing methods because of its properties and ecology. An obstacle to their development is the price of the available equipment used in this process. The article presents the concept of making individual elements of a powder feeder by 3D printing. The designs are equipped with a volumetric feeding system using a disk driven by an electric motor and a worm gearbox. The individual elements of the feeder were designed and based on the drawings; they were made using several types of 3D printers. The design and fabrication were limited to the use of a small number of parts made of metal including little machining. In the following part, a prototype of the feeder was made and tested. It was shown to have correct characteristics of its operation and, in particular, correct linear characteristics of powder feed rate from disk speed similarly to commercial devices. Tests of the made feeder indicate the possibility of its use in thermal spraying systems.

1 September 2025 in Materials
Verified
Journal Article
Open access
PDF file
GMGrzegorz Maciaszek
Grzegorz Maciaszek
KCKrzysztof Cioch
Krzysztof Cioch
ANAndrzej Nowotnik
Andrzej Nowotnik
DNDamian Nabel
Damian Nabel
In this study, the effects of plasma assistance on the electron beam physical vapour deposition (EB-PVD) process were investigated using an industrial coater (Smart Coater ALD Vacuum Technologies GmbH) equipped with a dual hollow cathode system. This configuration enabled the generation of a plasma environment during the deposition of the ceramic top coat onto a metallic substrate. The objective was to assess how plasma assistance influences the microstructure and thickness distribution of 7% wt. yttria-stabilised zirconia (YSZ) thermal barrier coatings (TBCs). Coatings were deposited with and without plasma assistance to enable a direct comparison. The thickness uniformity and columnar morphology of the 7YSZ top coats were evaluated by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The mechanical properties of the deposited coatings were verified by the scratch test method. The results demonstrate that, in the presence of plasma, columnar grains become more uniformly spaced and exhibit sharper, well-defined boundaries even at reduced substrate temperatures. XRD analysis confirmed that plasma-assisted EB-PVD processes allow for maintaining the desired tetragonal phase of YSZ without inducing secondary phases or unwanted texture changes. These findings indicate that plasma-assisted EB-PVD can achieve desirable coating characteristics (uniform thickness and optimised columnar structure) more efficiently, offering potential advantages for high-temperature applications in aerospace and power-generation industries. Continued development of the EB-PVD process with the assistance of plasma generation could further improve deposition rates and TBC performance, underscoring the promising future of HC-assisted EB-PVD technology.

31 March 2026 in Adhesives
Verified
Journal Article
Open access
PDF file
GMGrzegorz Maciaszek
Grzegorz Maciaszek
DNDamian Nabel
Damian Nabel
JMJulia Maciaszek
Julia Maciaszek
In the present study, the influence of the parameters of the bonding process, namely the applied pressure during curing, as well as the duration and temperature of curing, on the tensile strength of the bonded joints was investigated. Pull-off tests were conducted in accordance with the ASTM C633 standard. The samples were bonded using a single-component thermosetting adhesive, HTK Ultra Bond 100. On the basis of the results obtained, it was concluded that the tensile strength of the bonded joint, and thus its overall quality, is strongly influenced by the curing parameters of the thermosetting adhesive. The most effective bonding conditions were identified.