This paper proposes to use an upgraded version of the Multifil simulation tool to model an ITER TF-like conductor in two cases: In tokamak and in cold test conditions. After briefly introducing the Multifil code, the paper will report the latest upgrades in terms of thermal equilibrium as well as simultaneous Lorentz and coil operational loads. We will present a new post-processing of the fractured filamentary area, which relies on a memory of the fracture map along all the loading steps. Then, considering ITER is currently building a magnet coil test bench (MCTB) with the capability to cold test some of the TF coils at nominal current (68 kA) in a standalone situation, we will discuss how mechanical modelling of the TF conductor is relevant for assessing the impact of the test sequence on the Nb3Sn conductor degradation. We will present a new loading sequence, representative of the test facility conditions, with a different Lorentz force direction and amplitude with respect to tokamak operation. Furthermore, the MCTB test implies an additional over-compression of conductors located in the straight leg of the TF coil in equatorial plane. The effect of this “cold-test cycling” will be discussed in terms of mechanical behavior, fracture of strands and tentative Tcs degradation estimation.
For the large-scale fusion magnets of the International Thermonuclear Experimental Reactor (ITER) tokamak, wound with cable-in-conduit conductors, the application of sophisticated numerical models able to analyse the thermal–hydraulic behaviour during plasma scenarios is of paramount importance to guarantee an adequate stability margin during operating conditions. The SuperMagnet code has been developed by CryoSoft with the intent to simultaneously simulate the electrical, thermal and hydraulic phenomena occurring during the operation of superconducting coils. In this work, the SuperMagnet code is applied to analyse the thermal–hydraulic behaviour of the central solenoid of the ITER tokamak under the plasma scenario. The central solenoid (CS) is composed of six modules for a total amount of 240 pancakes. The software is able to tackle the complex structure of the CS and its cryogenic closed loop. In the present work, the circulation pump operation and the heat transfer to the helium bath are investigated. The results presented here show the temperature evolution of the magnet and of the supercritical helium during the plasma scenario, which allows the determination of the operation margin of the CS.
20 January 2025 in IEEE Transactions on Applied Superconductivity
The ITER Central Solenoid (CS) is under fabrication by the US ITER organization and its subcontractors. US ITER will supply seven modules to ITER IO, six of which will be assembled in a stack that forms the ITER Central Solenoid. All CS modules (CSM) were or will be tested at 40 kA in the Final Test facility at General Atomics (GA). CSM 5, 6, and 7 were tested in 2023 and 2024. Some instrumentation was updated to obtain information on the suppression of the inductive noise in the CSMs at high dB/dt events, which will lead to improved quench detection and protection of the modules. All the standard tests performed on previous CSMs to validate the properties of the CSM have also been performed on CSMs 5-7 to confirm the consistency of the CSM properties for ITER CS. The Tcs margin demonstration was done for the first time at the GA Facility on CSM6. Test results and analysis are presented and discussed.
17 February 2025 in IEEE Transactions on Applied Superconductivity
The nineteen ITER Toroidal Field (TF) coils (including a spare one) consists of seven double pancakes (DP) of cable-in-conduit conductors (CICC), each containing 900 superconducting Nb3Sn strands. In total eight strand manufacturing companies were involved, either relying on the bronze route or internal tin process. As a result, the strand, and thus conductor, performance can vary significantly within the same TF coil. This peculiarity inherent to the ITER project makes the evaluation process of coils stability, linked to the current sharing temperature (Tcs), more delicate. Following an extensive conductor testing campaign carried out over several years within the SULTAN facility, degradation of the different TF conductors was observed along electromagnetic and thermal cycling. Relying on the ITER critical current scaling law and associated parameters for TF strands, effective strain properties and n-values were extracted from the SULTAN Tcs measurements. In parallel, recent simulations conducted with MULTIFIL (mechanical code) on TF CICC have shed some light on the strands mechanical state after cool-down and along electro-magnetic cycling, highlighting the importance of the bending strain. Capitalizing on these results, on the SULTAN database, and on the literature (already mentioning the bending strain effect on conductor degradation), we aim at refining the existing methodology of performance scale-up from strands to conductors by introducing the bending strain. Ultimately, we apply the model in an attempt to conciliate SULTAN Tcs measurements and MULTIFIL mechanical results.
30 November 2023 in IEEE Transactions on Applied Superconductivity
The ITER magnet system contains 50 GJ of energy in 3 main coil sets and feeders. Lesson learned from arc incidents in JT-60SA and CS module 3 cold test show the consequences of insulation failure. There are three major insulation challenges in ITER magnets: bulk insulation in the coil, ground insulation and high voltage wiring. The most issues are found at the vacuum interface with Paschen breakdown in poor vacuum leading to arcs from ground insulation and the risk of high voltage wire insulation cracking. High voltage arcing can potentially be a safety concern in ITER due to arcing to the vacuum vessel. The mitigation focuses in 3 main areas: Prediction: Simulation of arc development within the cryostat to assess potential damage and if necessary implementation of extra protection; Prevention: Minimisation of weak areas, notably high voltage (HV) wire exits from ground insulation. As a result of failure root cause analysis, chemical corrosion between coil resin and wire insulation is a concern being investigated, with if necessary quick “universal” solutions to repair or reinforce predicted weak areas. Vacuum monitoring in the cryostat is being improved to identify potential Paschen conditions in advance; Early Detection: Implementation of regular intermediate global electrical tests under controlled Paschen conditions at low temperature to detect breakdown with high sensitivity of leakage currents (∼10 µA) which may in turn require room temperature water cooled busbars to be easily isolated. At least initially, in-cryostat cameras or other spark detection methods are needed to localise failures and repair methods need to be pre-qualified.
19 June 2024 in IEEE Transactions on Applied Superconductivity
The ITER superconducting magnet electrical insulation is designed and manufactured to be Paschen proof. The ITER cryostat and the feeder vacuums are also designed to provide a level of vacuum where Paschen conditions should not occur in case of insulation failure. The high voltage insulation failure coincident with degraded vacuum has been identified as a risk with major consequences. The level of magnetic energy stored in the superconducting coils, up to a maximum value of about 50 GJ, could result in electrical arcs leading to severe damages on the magnet system. The present paper focus on the operation, control and protection to mitigate the risk of Paschen discharge: vacuum monitoring, detection and protective actions are discussed: what the baseline strategy is and what should be further developed and improved for the ITER magnet system based on the return of experience of large scale superconducting magnet tests.