13 January 2021 in IEEE Transactions on Applied Superconductivity
AC losses deposited in the magnets during JT-60SA commissioning and operation will both affect the local stability of the conductor and act as a load on the cryogenic system. Our objective is thus to establish a detailed modeling of AC losses generated in the magnets by different current scenarios. Since the TF coils have been tested in the Cold Test Facility (CTF) and will be the first ones to be fully energized during the commissioning, we have focused our work on the AC losses deposited in the TF; this enables us to assess the relevancy of our modeling against the CTF data. We also present thermohydraulic simulations conducted with TACTICS (a CEA tool coupling THEA and Cast3m) to both have a view on heat load propagation inside TF winding pack and estimate the impact on the helium temperature of the AC losses generated by the TF fast discharge during the cold tests and the commissioning.
21 December 2016 in IEEE Transactions on Applied Superconductivity
Cable-in-conduit conductors (CICCs) are composed of a large number of strands (superconducting composites and copper strands) twisted together in several stages with different twist pitches. They are widely used in large fusion tokamaks such as JT-60SA or ITER. However, because of their complex transposed geometry at a strand scale, the knowledge of ac coupling losses in these conductors is limited and still has some improvement margins to capture its complexity while the prediction of their behavior under transient regimes (e.g., central solenoid) is of first importance to assess a safe operation in tokamaks. Consequently, we have carried out an in-depth theoretical generic study of a single stage of a CICC and analytically derived the expression of coupling losses using physical parameters (time constant and partial shielding coefficient) determined from electromagnetic and geometrical properties. Our approach has been inspired by the MPAS model (extensively used on the experimental ITER database) but starts from the analytical description of a single stage and aims at reaching the CICC scale in an iterative way.
12 December 2024 in IEEE Transactions on Applied Superconductivity
This paper proposes to use an upgraded version of the Multifil simulation tool to model an ITER TF-like conductor in two cases: In tokamak and in cold test conditions. After briefly introducing the Multifil code, the paper will report the latest upgrades in terms of thermal equilibrium as well as simultaneous Lorentz and coil operational loads. We will present a new post-processing of the fractured filamentary area, which relies on a memory of the fracture map along all the loading steps. Then, considering ITER is currently building a magnet coil test bench (MCTB) with the capability to cold test some of the TF coils at nominal current (68 kA) in a standalone situation, we will discuss how mechanical modelling of the TF conductor is relevant for assessing the impact of the test sequence on the Nb3Sn conductor degradation. We will present a new loading sequence, representative of the test facility conditions, with a different Lorentz force direction and amplitude with respect to tokamak operation. Furthermore, the MCTB test implies an additional over-compression of conductors located in the straight leg of the TF coil in equatorial plane. The effect of this “cold-test cycling” will be discussed in terms of mechanical behavior, fracture of strands and tentative Tcs degradation estimation.
26 April 2022 in IEEE Transactions on Applied Superconductivity
During the integrated commissioning of JT-60SA tokamak, the Toroidal Field (TF) magnet has experienced fast current discharges which have induced AC losses in its winding packs (WP) and in its casings. Using the thermo-hydraulic sensors network installed at the inlet and outlet of the TF coils, we have performed enthalpy balances to estimate the transient heat loads generated by AC losses. In parallel, we have modeled the hysteresis and coupling losses produced in the WP and the eddy currents losses produced in the casings by such events. We then assess and discuss the consistency between these experimental and first theoretical analyses from the energy balance point of view.
13 January 2019 in IEEE Transactions on Applied Superconductivity
The future circular collider (FCC) will require 696 double-aperture lattice sextupoles, 9336 single-aperture sextupole corrector magnets, and 480 double-aperture octupoles. The tunnel length and the overall integrated field of the main dipoles have to be kept constant so that the FCC can both reach the specified center of mass collision energy and fit into the Geneva basin. Considering these criteria, any reduction in the length of the other magnets can be traded in exchange for a reduced dipole field, which would result in an overall cost saving for the FCC. However, to be able to reduce the length of these sextupole and octupole magnets, their local strength has to be maximized. Consequently, in this paper, we first explore the maximum achievable local strength for these different magnet types for both Nb-Ti and Nb3Sn wire technology taking into account circuit and protection criteria. We then select and present a preferred design based on an overall cost and complexity reduction for the FCC.
7 February 2020 in IEEE Transactions on Applied Superconductivity
Due to the High Luminosity upgrade of the Large Hadron Collider (HL-LHC), the orbit corrector dipoles located just before the interaction points of the accelerator will receive significantly increased gamma radiation doses, i.e. up to 20 MGy over the HL-LHC lifetime. Since these magnets were not designed to withstand such high gamma doses, new MCBC and MCBY magnets have to be designed and produced using radiation hard impregnation insulation and materials. In this paper, we describe both the gamma radiation campaign we are performing to determine the radiation hardness of the present MCBC and MCBY magnets and the new design and technologies that we have selected for the manufacturing of radiation hard spare units. We also discuss the impact of failing MCBC and MCBY magnets on the LHC and the foreseen alternative solutions.