Svajunas Juociunas

Mr. Svajunas Juociunas


Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 December 2020 in Buildings
Verified
Journal Article
Open access
PDF file
ARAudrė Rugytė
Audrė Rugytė
Mindaugas DaukšysMindaugas Daukšys
Mindaugas Daukšys
SJSvajunas Juociunas
Svajunas Juociunas
Ruben Paul BorgRuben Paul Borg
Ruben Paul Borg
The interaction between concrete and steel occurs during concrete mixing and finishing processes, during filling of concrete moulds, formwork, composite columns and during pumping of concrete mixtures. More experimental investigation is required to predict variations in interface friction, as a result of the composition of the lubrication layer which depends on the composition of concrete. This study provides experimental results to allow for a better understanding of friction at concrete-steel interface, with changes in the coarse aggregate (CA) content in the aggregate mixture (AM). Friction tests on fresh concrete have been carried out using the BTRHEOM tribometer (Nantes, France) and the interface parameters were calculated on the basis of the interface friction between the concrete and the steel wall, through the ADRHEO software. The roughness parameters were measured along the length of the rotary steel cylinder of the tribometer. In addition, the roughness of new and modified metal form-lining in steel composite columns was also measured. Variations in the CA content in the AM in the 42 to 52% range had minimal effects on the yield stress of the interface. The viscous constant of the interface as measured with a tribometer decreased, when the roughness parameter Rt values of the rotary cylinder wall, which refer to the absolute vertical distance between the maximum profile peak height and the maximum profile valley depth along the sampling length, were in the 17.10 to 28.73 μm range. The roughness profile peaks’ asperity recorded, was higher for the worn metal form-lining and for the steel composite columns with the inner surface covered in rust, when compared to the rotary cylinder roughness profile. The hypothesis is based on the principle that a sufficient lubrication layer, with the required thickness of fine mortar is created at the interface between the concrete and the metal form-lining or steel composite column wall, when the CA content in the AM varies in the range from 42 to 52% and the wall roughness parameters (Rt) of these elements varies in the 15.00 to 30.00 μm range.

26 June 2012 in Engineering Structures and Technologies
Verified
Journal Article
Closed access
VŽVigantas Antanas Žiogas
Vigantas Antanas Žiogas
SJSvajunas Juociunas
Svajunas Juociunas
VMVioleta Medelienė
Violeta Medelienė
GŽGiedrius Žiogas
Giedrius Žiogas
The exploitation time and reliability of monolithic reinforced concrete structures largely depend on concreting technology and process influence during concreting and early setting stages. Different types of cracks in monolithic reinforced concrete structures appear due to internal and external effects. Cracks appear when the technology of structure concreting is damaged, when formwork is removed during the further setting and structures loaded period. In order to avoid micro and macro cracks in monolithic structures, it is important to measure the particular setting time moment and technological process moment when stresses that exceed the permissible values appear in concrete. The article analyses the processes that appear when horizontal, sloping and vertical monolithic reinforced concrete structures are concreted. The analysis of concrete mixture pressure on formwork is performed. The pressure which is calculated according to different countries’ methodology is different: the smallest pressure is obtained calculating according to the British recommendations, and the largest pressure is obtained according to French CIB recommendations. In Lithuania, it is recommended to follow the German DIN 18218 standard. The balance conditions of concrete mixture concreting on slope surface are described. The main concreting technology parameters and their interaction are analysed; the speed, intensity and time of continuous concreting technology are presented. When the process of continuous concreting is performed, it is necessary to evaluate the interaction and values of parameters properly. Methodical theoretical calculation is presented. Practical solutions for industrial building construction applying the modern sliding formwork technology are presented. The impact of cement type, superplasticizers and temperature over the concrete mixture mobility, changes, fresh concrete structural strength and concrete setting kinetics are analysed. The main characteristics of the initial setting — the beginning of structure formation, when concrete mixture turns into concrete state — is analysed applying the ultrasonic method. The beginning of structure formation influences the regulated time of concrete mixture laying and compaction. The requirements for structural strength (permissible strength limits) and concreting rate (formwork movement) of freshly formed concrete are set when the construction is performed applying the continuous concreting technology method. The analysis is implemented performing the construction of cylindrical sludge tank with slipping formwork. While performing the analysis during concreting, it was stated that the concrete setting kinetics corresponds to the sludge tank concreting rate. The analysis performed after concreting and in 28 days of hardening revealed that there are no surface defects or cracks, and concrete strength exceeds the required sludge tank design strength. Santrauka Monolitinių gelžbetoninių statinių konstrukcijų eksploatacijos trukmė ir patikimumas daugiausia priklauso nuo betonavimo technologijos ir procesų poveikių betonavimo bei pradinio kietėjimo metu. Straipsnyje nagrinėjami procesai, vykstantys betonuojant horizontaliąsias, nuožulniąsias ir vertikaliąsias monolitines gelžbetonines konstrukcijas. Atlikta betono mišinio slėgio į formas analizė. Tiriami pagrindiniai betonavimo technologijos parametrai, analizuojamas jų ryšys, pateikiamas nepertraukiamo betonavimo technologijos betonavimo greitis, intensyvumas, trukmė. Atlikti teoriniai skaičiavimai ir siūlomi praktiniai sprendimai pramoninių statinių statybai, naudojant šiuolaikinę slankiųjų klojinių technologiją. Ištirta cemento tipo, superplastiklių, temperatūros įtaka šviežiai suformuoto betono struktūriniam stipriui ir betono kietėjimo kinetikai. Nustatyti reikalavimai šviežiai suformuoto betono struktūriniam stipriui, betonavimo greičiui (klojinių kėlimui), vykdant statybą nepertraukiamos betonavimo technologijos metodu. Tyrimai pritaikyti vykdant cilindrinio dumblo pūdytuvo statybą slankiaisiais klojiniais.

1 January 2009 in Statybinės Konstrukcijos ir Technologijos
Verified
Journal Article
Open access
VŽVigantas Antanas Žiogas
Vigantas Antanas Žiogas
SJSvajunas Juociunas
Svajunas Juociunas
GŽGiedrius Žiogas
Giedrius Žiogas

5 November 2020 in Journal of Sustainable Architecture and Civil Engineering
Verified
Journal Article
Open access
PDF file
Mindaugas DaukšysMindaugas Daukšys
Mindaugas Daukšys
VGVytenis Girčys
Vytenis Girčys
SJSvajunas Juociunas
Svajunas Juociunas
In this study three already finished projects in Lithuania were investigated, the problems faced in the projects were examined, and the main advantages and drawbacks of the chosen geopile installation technology were identified. Three alternative solutions for geopile installation were selected for the investigation: driving a hollow steel pipe into the ground using a deep vibrator and using geosynthetic material to reinforce soils (A1); driving a closed-ended hollow steel pipe into the ground and using geosynthetic material to reinforce soils (A2); driving an open-ended hollow steel pipe into the ground and using geosynthetic material to reinforce soils (A3). Those alternatives were evaluated according to the following criteria: geopile installation cost (K1), level of mechanization (K2), load bearing capacity (K3), installation options (K4), impact on the environment (K5), duration of the installation of geopiles (K6). In order to find out the significance of the evaluation criteria a survey questionnaire and a ranking procedure were used. The same order of criteria importance, namely K1˃K3˃ K2˃K4˃K6˃K5, was obtained using the selected rank-order weighting method. Basing on the selected criteria, a rational option for geopile foundations was identified using the multi-criteria assessment method TOPSIS. The results show that driving an open-ended hollow steel pipe into the ground and using geosynthetic material to reinforce soils (A3) is the most rational option for the installation of geopiles in the investigated finished projects in Lithuania. This article is based on Master thesis topic “Research on installation technology of geopiles”.

10 April 2020 in Journal of Sustainable Architecture and Civil Engineering
Verified
Journal Article
Open access
PDF file
Mindaugas DaukšysMindaugas Daukšys
Mindaugas Daukšys
RKRokas Kudirka
Rokas Kudirka
SJSvajunas Juociunas
Svajunas Juociunas
The stability of conventional concrete mixture was investigated using an inclined plane method. The experiment consisted of two steps: first, the research was made to determine the influence of coarse aggregate content in aggregates mixture on the stability and sliding of concrete mixture, when the specimens of mixture are on the inclined plane without additional roughening of surface; second, the research was made to determine the influence of inclined plane surface roughening on the stability and sliding of concrete mixture. During the research the condition was checked: the concrete mixture on the sloping plane will be stable, if the yield stress τ0 is higher than the shear stress τ in. (τ 0 ≥ τ). The shear stresses and rheological property yield stresses of conventional concrete mixtures were calculated analytically by using an empirical formula. Test results showed that the increase of coarse aggregate (4/16 fraction gravel) content from about 417 to 1175 kg in concrete mixture is enough to achieve the stability of concrete mixture, when plane inclination angles are 25°, 35° and 45°, but not enough to stop sliding process. In this case, additional implements are needed to increase the adhesion of fresh concrete to the base. By using the inclined planes, which were coated with a special dimpled membrane and geotextile, the fresh concrete does not slide downwards by inclined plane.

31 March 2025 in Buildings
Verified
Journal Article
Open access
PDF file
IŠIgnas Šliogeris
Ignas Šliogeris
DRDonatas Rekus
Donatas Rekus
SJSvajunas Juociunas
Svajunas Juociunas
Ruben Paul BorgRuben Paul Borg
Ruben Paul Borg
Mindaugas DaukšysMindaugas Daukšys
Mindaugas Daukšys
The research presented in this article seeks to identify the possible causes of reinforcement shadows (RS) on the surface of concrete test specimen produced under laboratory conditions. Different hypotheses about RS were selected based on factory practices and simulated in the study. The test specimens were cast horizontally in contact with steel form-facing surfaces coated with a water-soluble release agent. In addition, two scenarios were analysed during specimen production: reinforcing mesh was fixed using plastic spacers or tie wire. The analysis of the reinforcement shadows was based on visual inspection, taking photos, surface moisture content measurements, and colour variation analysis using the Natural Colour System. It was concluded that RS, which are typically characterized by darker lines, can be defined by the percentage of black colour present in the shadowed area compared to the percentage of black colour in the surrounding area. This percentage can be quickly assessed on a factory scale using digital colour readers that provide timely information. The reduced concrete cover thickness from 35 mm to 10 mm revealed light horizontal dark lines on the exposed surface. It was hypothesised that the gap of less than 10 mm between the reinforcing bars and the steel form-facing plate, along with the sieving effect of the fresh concrete, can retard the cement paste hydration process, resulting in unhydrated ferrite phases that contribute to the dark colour of the unhydrated cement. The release agent sprayed on the steel form-facing surface straight through the reinforcing mesh created a RS effect of the reinforcement on the exposed concrete surface. The absence of a release agent under steel rebars decreased the wettability at the interface between the formwork and fresh concrete, resulting in dark lines during the curing process. It is important to avoid such cases when manufacturing precast reinforced concrete elements. Quantitatively assessing RS and proposing a standardized method for calculation and categorization could be a new research direction in the future.