Fine-grained composites with high impact resistance (intentionally armor plates) were prepared from inexpensive raw materials by forced SHS compaction in the Ti-B-N-Cu (I) and Ti-B-N-C-Cu (II) systems ([Cu] = 0–10 wt %). The materials synthesized under optimized conditions were practically pore-free compacts with the following parameters: porosity 0.4–1.2%; hardness 91.5–92.5 and 92.3–93.3 HRA; density 4.3–4,4 and 4.5–4.7 g/cm3, for systems I and II respectively. The materials were found to withstand impacts with an energy of 18000–20000 J (for materials with d = 6.8–6.5 g/cm2).
1 October 2021 in IOP Conference Series: Materials Science and Engineering
In the preformed work were studied the characteristics of Ni, Mo and Cu – free austempered ductile iron microalloyed by Boron under different contact load. For microalloying liquid cast iron with boron, the ferroboron by synthesized SHS - innovation technology was used. The upper and lower bainitic austempered ductile irons were studied with different content of metastable retained austenite. The experimental samples were tested with a fixed linear sliding speed of 2 m / s at a different contact load values, which were changed in the range of 25, 50 and 100 Newtons. It was defined that the value of the contact load has a significant effect on the tribotechnical characteristics of bainitic cast irons in conditions of dry sliding friction. Particularry, they determine the structural changes character and the degree of surface layers degradation of friction. High strength cast irons with the lower bainite structure are more resistant to adhesive wear. According to the obtained data, the presence of up to 80% metastable retained austenite in the metal matrix structure of the of experimental cast irons makes it possible to stabilize the friction coefficient under the investigated contact loads. Thus, to ensure maximum wear resistance, the isothermal quenching of high-strength cast irons must be carried out in the temperature range 220-280 0C with a minimum treatment time.
1 March 2019 in IOP Conference Series: Earth and Environmental Science
The aim of the study was to develop methods to reduce the penetration ability of the flame front and red-hot striking elements that propagate in the confined space of mines. In the article is considered a method for localizing explosions of a methane-dust mixture in coal mines, by creating an aqueous barrier (increased density) in the propagation path of the flame front and incandescent particles, using a high-energy pyrotechnic composition based on nanoaluminum. The optimal pyrotechnic composition contents of ammonium nitrate - 50%, smokeless powder- 45%, magnesium - 3% and nanoaluminum - 2%. This composition punched the target to a depth of 6.5 mm with a barrier thickness of 50 mm. Water cannon with a nozzle with a diameter of 80 mm, allows to localize the spread of the flame front.
Statistics shows that the majority of accidents with fatal outcome are caused by methane and/or coal dust explosion. This leads to assume that contemporary counter-explosion systems of various designs cannot be considered effective. Considering the growing threat of methane explosion in the coming years along with the development of deeper levels, the improvement of a system for protecting people in underground opening appears urgent. This paper focuses on technical solutions to be used in designing a protective system for minimizing the consequences of methane explosions in coalmines. The new protective system consists of three main modules: i) a high-speed shock wave suppression section; ii) a suppression section with a long-term action and iii) a system activating device. The shock wave suppressor contains a 200 litre volume water tank with a built-in gas generator and nozzles. It is activated after 12ms from the blast moment, the duration of discharge is 40 s. The suppression section with a long-term action contains a 2000 litre volume water tank, a high-pressure pump, a hydraulic accumulator, solenoid valves, and a system of pipes with built-in nozzles. It is activated after 4 s from the blast moment, the duration of discharge is 8 min. The activation device includes a detection block containing sensors, an emergency signal generation module, a signal transmission module, a signal receiving module and a power supply module. The system operates in a waiting mode and activates immediately upon the receipt of the start signal generated by the detector. The paper also addresses the preliminary results of the system prototype testing in the tunnel.