A circular economy is a current tenet that must be implemented in the field of construction. That would imply the study of the possibilities of the use of waste generated, for obtaining materials the used in construction as replacements for the raw material used. One of these possibilities is the substitution of the cement by slag, which contributes to the reduction of cement consumption, decreasing CO₂ emissions, while solving a waste management problem. In the present paper, different types of concrete made by cement substitution with different type of slags have been studied in order to evaluate the properties of these materials. Cement is replaced by slag from different steel mills, both blast furnace and ladle furnace slag. The percentages of slag substitution by cement are 30%, 40% and 50% by weight. Mechanical, physical and environmental properties have been evaluated. Compressive and flexural strength have been analysed as the main mechanical properties. As far as physical properties go, density and porosity tests were be reported and analysed, and from an environmental point of view, a leachate study was performed. It has been found that some kinds of slag (blast furnace slag) are very suitable as substitutes for cement, providing properties above those of the reference concrete, while other types (ladle furnace slag) could be valid for non-structural applications, contributing in both cases to a circular economy.

Concrete consumption greatly exceeds the use of any other material in engineering. This is due to its good properties as a construction material and the availability of its components. Nevertheless, the present worldwide construction increases and the high-energy consumption for cement production means a high environmental impact. On the other hand, one of the main problems in the iron and steel industry is waste generation and byproducts that must be properly processed or reused to promote environmental sustainability. One of these byproducts is steel slag. The cement substitution with slag strategy achieves two goals: raw materials consumption reduction and waste management. In the present work, four different concrete mixtures are evaluated. The 25% cement substitution is carried out with different types of slag. Tests were made to evaluate the advantages and drawbacks of each mixture. Depending on the origin, characteristics, and treatment of the slag, the concrete properties changed. Certain mixtures provided proper concrete properties. Stainless steel slag produced a fluent mortar that reduced water consumption with a slight mechanical strength loss. Mixtures with ground granulated blast furnace slag properties are better than the reference concrete (without slag).

This paper is part of a research line focused on the reduction of the use of cement in the industry. In this work, the study of work methodologies for the manufacture of green cementitious grout mixtures is studied. Grout is widely used in construction and it requires an important use of raw materials. On the other hand, the steel industry faces the problem of the growing generation of slag wastes due to the increase in steel manufacturing. The green grout aims to achieve the dual objective of reducing the demand for cement and improve the slag waste valorization. Slag is not introduced as an aggregate but through the direct replacement of cement and no additives. The research seeks a product where we can use steel slag intensively, guaranteeing minimum resistance and workability. Results with substitutions between a 25% to 50% and water/cement ratio of 1 are presented. In particular, the suitability of different slags (two Ladle Furnace Slag (LFS) and one Blast Furnace Slag (GGBS)) in the quality of the final product are analyzed. The feasibility of replacing cement with slag and the importance of the origin and pretreatment are highlighted.

This article presents a study of the main properties (consistency, workability, leaching, unsoundness, and mechanical properties) of cement grouts prepared with cement replacement by blast furnace slag (GGBS). Mixtures have been analyzed in the absence of additives and reached high replacement percentages. As shown in the different tests presented, the observed evolution of the resistance and workability of the mixtures makes them very interesting for its application. Different types of cement (CEM-I 42.5 and CEM-I 52.5 R) and different water/binder values (1 and 0.67) are used. The results present opportunities for the steel industry by the intensive valorization of slag waste. The reduction of the use of cement in construction is also one of the key aims of this line of research. Results show improvements in the mechanical response with good fresh state properties for substitution percentages up to 70%. It is verified with leaching analysis that these products have less impact on the environment.

Building construction and building operations have a massive direct and indirect effect on the environment. Cement-based materials will remain essential to supply the growth of our built environment. Without preventive measures, this necessary demand in cement production will imply a substantial increase in CO₂ generation. Reductions in global CO₂ emissions due to cement consumption may be achieved by improvements on two main areas: increased use of low CO₂ supplementary cementitious materials and a more efficient use of Portland cement clinker in mortars and concretes. The use of ground granulated blast furnace slag in concrete, as cement constituent or as latent hydraulic binder, is a current practice, but information of concrete with ladle furnace slag is more limited. Specific knowledge of the behavior of mixtures with steel slag in relation to certain properties needs to be improved. This paper presents the results of the shrinkage (total and autogenous) of five concrete mixtures, produced with different percentages of two different slags in substitution of cement. The results show that shrinkage of concrete with the two different slags diverges. These different characteristics of the two materials suggest that their use in combination can be useful in optimizing the performance of concrete.