11 September 2020 in Journal of Lightwave Technology
We have proposed and demonstrated novel twin-hole and dual-core optical fiber. We use the normal MCVD technology to fabricate a single core fiber preform with thin cladding. Then, we drill two small holes in the center and a side position in a pure silica rod and insert the fabricated single core fiber preform into the two holes, heating the combination preform until the three parts fused. Finally, we drill two larger holes close to the center core and twin-hole and dual-core are vertically distributed. In order to contain the shape of air hole, we fill nitrogen gas in the two holes against the ambient pressure, which make the holes collapse during the fiber drawing. The dual-hole may use as micro-containers to inject modulation medium and aside the center core, induced accumulated interaction between flow material and evanescent field of the center core, therefore, it can be used as a modulation function expanded fiber to fabricate a very compact in-fiber integrated device.
11 September 2020 in Journal of Lightwave Technology
We designed a novel dual-core fiber with a large side air hole near the center core, which microstructure optical fiber can integrate microchannel and interferometer in a single fiber. To fabricate this special optical fiber, first, we drill a small hole in the side of a standard single-core fiber preform, insert a thin-clad core preform into the small hole, and then heat and fuse together. Finally, we drilled a larger hole near the center core. In the process of drawing the fiber, the large hole should be filled with nitrogen at a constant pressure to prevent the hole from collapsing. The air hole of the special optical fiber can be used as a channel for microfluidic transmission, and the air hole is in close contact with the central core and away from the eccentric core, so this microstructure optical fiber is very suitable for use as a compact in-fiber integrated microfluidic sensors.
18 February 2025 in Optics Express
Optical fiber sensors have advantages such as small size and good biocompatibility, leading to widespread interest in the field of hand motion tracking. In this work, we designed a multi-core fiber Bragg grating Fabry-Perots (FBG-FPs) sensor based on FP interference theory. We inscribed short FBGs with different wavelengths in different fiber cores to form the FP, and then employed thermal diffusion technology for single-channel acquisition of the multi-core fiber FBG-FPs sensor. We also proposed a signal demodulation method for the FBG-FPs sensor based on the principal component analysis (PCA) algorithm and conducted experiments on strain, temperature, and bending sensing. The results indicate that the bending sensitivities of the three external cores exhibit strong dependence on bending, with a maximum sensitivity of 52.8 pm/m−1. The direction and curvature of bending can be reconstructed using the wavelength shifts obtained from the PCA algorithm. This sensor features a compact structure, flexible fabrication, and low cost, improving the adaptability to individual differences in optical fiber smart gloves and enhancing multiplexing sensing capabilities, thus providing broad prospects for the development of human-machine interfaces and medical health monitoring.
13 May 2024 in Journal of Lightwave Technology
We report the measurement of the reflection spectrum of a Fabry-Perot interferometer during the diffusion of dopants in optical fiber caused by high-temperature heating, thus indirectly and accurately obtaining the diffusion coefficient of the dopants. The diffusion coefficient of the dopant is measured through the wavelength shift of the interferometer spectrum when diffusion of the dopant from the core to the cladding results in a decrease in the refractive index of the core. The diffusion coefficient of germanium-doped single-mode fiber before and after hydrogen loading was measured. The results show that hydrogen in the fiber significantly enhances the diffusion rate of the germanium dopant. The measured germanium-doped diffusion coefficients are in good agreement with the results of previous studies. Our proposed method of dopant diffusion coefficient measurement is simpler and more convenient. Accurate characterization of dopant diffusion coefficients in optical fibers helps to accurately understand the dopant diffusion process and is particularly important for the fabrication of various optical fiber-integrated optical devices using thermal diffusion techniques.
27 June 2025 in Optics Express
We propose and construct the optical palm based on the seven-core optical fiber for particle trapping, multidimensional particle shooting, and controllable vibrations. This optical hand features a tunable three-dimensional optical trap, created using six independently controlled surrounding fiber cores and one central fiber core. By employing a signal generator to regulate the output optical power of each laser channel, we achieve photodynamic manipulation of the trapping particles. Through theoretical analysis and experiments, we discover that under two specific power configuration schemes, micro-particles can travel hundreds of micrometers along the direction of emitted light, reaching a maximum velocity of up to 404.43 μm/s. In the controllable vibration configuration, we achieve multidimensional controllable light-induced vibrations of the particles. Lastly, we find that in the symmetrical dual-core output light intensity phase difference modulation scheme (the dynamic manipulation of particles is achieved through active phase modulation of the light transmitted by a symmetrically arranged dual-core), the vibration amplitude of the micro-particles can be controlled by the phase difference of the modulation signal of the dual beam transmission light intensity, enabling the particles to be immobilized at Δφ=180°. Our proposed method extends the potential applications of optical manipulation based on optical fibers, such as in the multidirectional classification of micro-particles in biology and the induction of micro-cell vibrations to achieve uniform distribution of fluorescent markers within cells.