A ubiquitous experiment to characterize the formability of sheet metal is the simple tension test. Past research has shown that if the material is repeatedly bent and unbent during this test (i.e., Continuous-Bending-under-Tension, CBT), the percent elongation at failure can significantly increase. In this paper, this phenomenon is evaluated in detail for AA-6022-T4 sheets using a custom-built CBT device. In particular, the residual ductility of specimens that are subjected to CBT processing is investigated. This is achieved by subjecting a specimen to CBT processing and then creating subsize tensile test and microstructural samples from the specimens after varying numbers of CBT cycles. Interestingly, the engineering stress initially increases after CBT processing to a certain number of cycles, but then decreases with less elongation achieved for increasing numbers of CBT cycles. Additionally, a detailed microstructure and texture characterization are performed using standard scanning electron microscopy and electron backscattered diffraction imaging. The results show that the material under CBT preserves high integrity to large plastic strains due to a uniform distribution of damage formation and evolution in the material. The ability to delay ductile fracture during the CBT process to large plastic strains, results in formation of a strong fiber texture throughout the material.

The implementation of a phase-field model in finite elements usually requires significant expertise and involves the development of a user element with additional degrees of freedom. An alternative implementation of the phase-field model within a thermo-mechanical finite element simulation package was presented in (Cho et al 2012 Int. J. Solids Struct. 49 1973–1992), where the phase-field variable is treated as the temperature degree of freedom. However, this approach has only been used for small strain phase-field modelling of martensitic transformations and quasistatic phase-field modelling of fracture. In this work, we present a phase-field finite element implementation via the temperature degree of freedom for several additional cases from the literature: (i) the large-strain phase-field description of deformation twinning presented in (Clayton and Knap 2011 Physica D 240 841–858), (ii) phase-field description of brittle fracture with inertial effects based on the theory from (Molnár and Gravouil 2017, Finite Elem. Anal. Des. 130 27–38) and (Miehe et al 2010 Int. J. Numer. Methods Eng. 83 1273–1311) and (iii) the classical Stefan problem of solidification presented in (Mackenzie and Robertson 2002 J. Comput. Phys. 181 526–544). The last problem involves the temperature and phase-field variables as unknowns.

During magnetic pulsed welding (MPW), a wavy interface pattern can be observed. However, this depends on the specific material combination being joined. Some combinations, e.g., steel to aluminum, simply provide undulating waves, while others, e.g., titanium to copper, provide elegant vortices. These physical features can affect the strength of the joint produced, and thus a more comprehensive understanding of the material combination effects during MPW is required. To investigate the interfacial morphology and parent material properties dependency during MPW, tubular Al1100 and various copper alloy joints were fabricated. The influence of two material properties, i.e., yield strength and density, were studied, and the interface morphology features were visually investigated. Results showed that both material properties affected the interface morphology. Explicitly, decreasing yield strength (Cu101 and Cu110) led to a wavy interface, and decreasing density (Cu110 and CP-Ti) resulted in a wave interface with a larger wavelength. Numerical analyses were also conducted in LS-DYNA and validated the interface morphologies observed experimentally. These simulations show that the effect on shear stresses in the material is the cause of the interface morphology variations obtained. The results from this research provide a better fundamental understanding of MPW phenomena with respect to the effect of material properties and thus how to design an effective MPW application.

In Electrical-Assisted Forming (EAF), current is passed through the material during the deformation process, which results in a decrease in the required flow stress for the material. While resistive heating occurs, the flow stress reductions are beyond what can be explained by temperature effects alone. Hypotheses for this effect relate to the current affecting dislocation generation and aiding dislocation motion through the lattice structure. If the latter was the case, then materials with higher dislocation densities from severe deformation should have more pronounced benefits from EAF. In this research, Equal Channel Angular Extrusion (ECAE) was used to induce severe plastic deformation into the material. Subsequent EAF compression experiments with the ECAE specimens and as-received material with comparable grain sizes were conducted. As expected, the EAF process reduced the flow stress value substantially more, e.g., 224MPa versus 115MPa at a strain of 0.8 for the ECAE specimens compared to the as-received specimens respectively. These flow stress reductions were from a case with no current applied to a case where an initial current density of 250A/mm2 was applied. EAF may particularly be beneficial at the microscale to address size effects as the current required to achieve an elevated current density is more viable.