Soybean plants cultivated using mulched drip irrigation planting technology have the following characteristics during the harvest period: green stems and leaves, and a high straw/grain ratio. Moreover, the threshing device of a soybean combine harvester is difficult to adapt to, resulting in an increase in the accumulation and unevenness of the threshed mixture. This leads to an increase in impurity content and the loss rate. We conducted a single-factor experiment on a self-developed longitudinal/axial-flow soybean threshing and separation test bench, employing drum speed, feeding rate, and threshing clearance as experimental factors. The influence of the soybean threshing and separation device’s working parameters on the distribution and uniformity of the threshed mixture in the axial and radial directions of the drum was explored through experiments. The results showed that the mass of the threshed mixture and soybean seeds showed a trend of first rapidly increasing and then slowly decreasing in the axial direction of the drum. Additionally, the mass showed a distribution feature of large values on both sides and small values in the middle in the radial direction. A lower drum speed, greater threshing clearance, and a smaller feeding rate make the radial distribution of a threshed mixture more uniform. Based on the combination of the crushing rate and unthreshed rate, the optimal working parameter combination was determined to be as follows: a drum speed of 500 r/min, a feeding rate of 6 kg/s, and a threshing clearance of 25 mm. The findings of this research offer valuable insights for the structural optimization and design enhancement of threshing and cleaning mechanisms within soybean combine harvesters.

Inadequate parameter design of the cleaning device in soybean combine harvesters leads to elevated levels of machine harvesting losses and impurity rates. To provide fundamental data for the optimization of structural parameters of soybean cleaning sieves, it is of great significance to study the collision and bouncing characteristics of soybeans on the cleaning sieve surface and the impact of parameters on the coefficient of restitution (COR). The current study designed a collision platform, using soybeans at the harvest stage as the research subject. The experimental factors included drop height, wall inclination angle, wall movement speed, and wall material. Through single-factor experiments and orthogonal experiments, the effects of different collision parameters on the rebound trajectory and COR of soybeans were investigated. This study focuses on soybeans at the harvest stage as the test subjects. Experiments were conducted on a collision platform and recorded with a high-speed camera to capture the three-dimensional motion trajectories of the soybeans using the principle of specular reflection. Through single-factor experiments, the jumping characteristics of the soybeans on sieve surfaces with different motion characteristics were analyzed. The impact of drop height (400–650 mm), wall inclination angle (8–13°), wall movement speed (0.6–1.1 m/s), and wall material (stainless steel plates and polyurethane plates) on the coefficient of restitution (COR) was calculated and clarified. Multi-factor orthogonal experiments were conducted to determine the significance order of the different factors affecting the COR. Three-dimensional models of the soybeans and the collision platform were constructed using SolidWorks software, and the collision between the soybeans and the cleaning wall was simulated using EDEM software. The micro-forces and energy transfer during the soybean collision were analyzed. The results indicated that the COR of soybeans decreases as the drop height increases, but increases with wall inclination angle and wall movement speed. Additionally, the COR is higher when the soybeans collide with stainless steel plates compared to polyurethane plates. The order of influence of the four factors on the COR were: wall material > wall inclination angle > wall speed > drop height. This study provides important reference value for the efficient and low-loss design of cleaning devices.

In order to solve the problems of bottom pod leakage and soil removal by header, a soybean header profiling system was designed in this paper. The cutter height off-ground detection device was installed on both sides of the header, and the cutter distance from the ground was represented by the angle sensor turning when the profiling wheel met the rolling ground. The hydraulic electromagnetic reversing valve was installed so that the profiling system could automatically control the lifting of the header, the unilateral power of the solenoid valve was 0.15 s, and the height of the cutter from the ground was changed by 10 mm. The height of the cutter off the ground was set to 80 mm, and the adjustment range of the soybean header profiling system was 45–125 mm. The test results showed that the maximum absolute error of the cutter off the ground height detection device was 5.98 mm, the minimum absolute error was 1.00 mm, and the relative error was 0.038. The cutter height adjustment device was powered for 0.15 s, and the average adjustment distance was 11.158 mm. The soybean header profiling system did not shovel soil during field harvest, and the stubble height of 85% of soybean plants was less than 10 mm from the set height after harvest. The results showed that the soybean header profiling system could effectively adjust the cutter height from the ground so that the cutter height from the ground was kept at 80 mm. This study could provide a reference for the intelligent design of soybean harvesters.

Soybeans are a crucial crop, and it is therefore necessary to make accurate predictions of their mechanical properties during harvesting to optimize the design of threshing cylinders, minimize the breakage rate during threshing, and enhance the quality of the final product. However, a precise model for the mechanical response of soybean seeds under stress conditions is currently lacking. To establish an accurate finite-element model (FEM) for soybeans that can predict their mechanical behavior under various loading conditions, an ellipsoidal modeling approach tailored for soybeans is proposed. Soybeans harvested in Xinjiang were collected and processed as experimental materials; the average moisture content was 11.77%, there was an average density of 1.229 g/cm³, and the average geometric specifications (height, thickness, and width) were 8.50 mm, 7.92 mm, and 7.10 mm, respectively. Compression tests were conducted on the soybeans in vertical, horizontal, and lateral orientations at the same loading speed to analyze the load and damage stages of these soybeans harvested in Xinjiang. The experimental results indicate that as the contact area decreases, the crushing load increases, with soybeans in the horizontal orientation being able to withstand the highest ultimate pressure. When placed vertically, the soybeans are not crushed; in horizontal and lateral orientations, however, they exhibit varying degrees of breakage. The Hertz formula was simplified based on the geometric characteristics of soybeans, and the elastic moduli in the X, Y, and Z directions of the soybean seeds were calculated as 42.8821 MPa, 40.4342 MPa, and 48.7659 MPa, respectively, using this simplified Hertz formula. A model of the soybeans was created in SolidWorks Ver.2019 and imported into ANSYS WORKBENCH for simulation verification. The simulation results were consistent with the experimental findings. The research findings enhance the understanding of the mechanical behavior of soybean seeds and provide robust scientific support for the optimization of soybean processing technologies and the improvement of storage and transportation efficiency.

Cumin (Cuminum cyminum L.) is a globally important spice crop, particularly significant in Xinjiang, China, where it is extensively cultivated in cotton–cumin intercropping systems. This review concentrates on the serious bottleneck hindering the development of the cumin industry: the low level of harvesting mechanization. Traditional manual harvesting methods are labor-intensive, inefficient, and result in high yield losses. This paper fully explores the prospects and challenges of mechanizing cumin harvesting in accordance with the particular biological characteristics of cumin plants and the complexity of intercropping systems. We review the current status of research in the following domains: (1) cumin biological traits and intercropping models; (2) grain loss and stalk damage patterns in stripper harvesting of similar crops; (3) factors influencing root–soil interaction during mechanical extraction; (4) uprooting–conveying harvesting techniques and row division/plant singulation methods applicable to root and tuber crops; and (5) cumin-threshing and -cleaning technologies. This review highlights the inadequacy of current grain-harvesting machinery for cumin and underscores the urgent need for specialized, low-loss harvesting technologies tailored to cumin’s delicate nature and intercropping context. Finally, we propose future research directions to overcome these mechanization challenges and promote the sustainable development of the cumin industry.

Existing cleaning devices for edible sunflower have a low cleaning efficiency, high cleaning loss rate, and high impurity rate; therefore, a wind-sieve-type cleaning device for edible sunflower harvesting was designed. According to the characteristics of dislodged objects, a vibrating screen for the device was designed, and the dislodged edible sunflower objects in the device were used for a mechanical analysis of the force conditions to determine the displacement of the different edible sunflower objects dislodged by the action of airflow. Using FLUENT-DEM gas–solid coupling simulation technology, the velocity of the flow field, the velocity vector, and the trajectory of the dislodged objects inside the cleaning device were analyzed, and the law of motion applied to the airflow and the dislodged objects inside the device was clarified. According to the results of the coupled simulation analysis, the key factors affecting the operation of the cleaning device were wind speed, vibration frequency, and amplitude. Based on the key factors of wind speed, vibration frequency, and amplitude, an orthogonal rotary combination test was carried out with the loss rate and impurity rate of cleaned grains as the evaluation indexes, and the test parameters were optimized to obtain the optimal combination of operating parameters of the device, which were as follows: wind speed: 30 m·s⁻¹; vibration frequency: 8.44 Hz; and amplitude: 41.35 mm. With this combination of parameters, the seed loss rate and impurity rate reached 3.47% and 6.17%, respectively. Based on the optimal combination of operating parameters, a validation test was performed, and the results of this test were compared with the results of the test bench using this combination of parameters. The results show that the relative errors of the loss rate and impurity rate between the bench test and the simulation test were 3.45% and 3.07%, respectively, which are less than 5%, proving the reliability of the simulation analysis and the reasonableness of the design of the test bench.