Due to its suitability to combine the radar and communication (RadCom) applications simultaneously, the integrated RadCom systems using orthogonal frequency division multiplexing (OFDM) signals have been widely investigated. However, the Doppler processing strategy in traditional OFDM radars exhibits low accuracy along with high complexity caused by the communication data bits conveyed on the OFDM chirps. In this letter, we propose a high accuracy Doppler processing method for the phase-coded OFDM-based RadCom system. The system complexity can also be reduced by adopting the low sampling rate, frequency domain-based correlation processing method. Simulation results validate our analysis, and show that the presented strategy outperforms traditional ones.
Stepped-carrier orthogonal frequency division multiplexing (SC-OFDM) radar is an emerging low-cost alternative to traditional OFDM radar for automotive applications. It offers high-range resolution without increasing the sampling rate. However, it suffers from the Doppler intolerance in high-speed target detection, which arises from Doppler-induced inter-carrier interference (ICI), resulting in peak power loss and increased range sidelobes in the range-velocity map. In addition, the maximum unambiguous velocity is reduced by the number of frequency steps. This paper proposes a novel range-Doppler processing method for nonlinear stepped-carrier OFDM (NSC-OFDM) radar systems to mitigate the problems. The proposed method employs a two-stage Doppler compensation approach: initially applying all-cell Doppler correction under unambiguous velocity assumption, followed by ambiguous-cell Doppler correction for ambiguous targets identified through range sidelobes. The method can automatically resolve velocity ambiguity by selecting the hypothesis with optimal sidelobe suppression, achieving effective ICI mitigation. Finally, simulation results validate the effectiveness of the proposed method; meanwhile, the good performance of the proposed method on range sidelobe reduction, estimation accuracy, and computational complexity are shown by comparisons with three other methods.
Conventional multiple‐input multiple‐output orthogonal frequency division multiplexing (MIMO‐OFDM) radar systems typically adopt the equidistant subcarrier interleaving (ESI) scheme to generate orthogonal transmit (TX) waveforms in the frequency domain. However, the ESI scheme is limited by a reduced unambiguous distance and distance‐dependent angle errors. To mitigate these issues, this paper proposes a hybrid range‐ and Doppler‐division multiplexing (RDM‐DDM) scheme for MIMO‐OFDM radar, which separates TX signals in both the distance and velocity domains. We first establish the signal model for the hybrid MIMO‐OFDM radar system. At the receiver, we implement distance–velocity–angle processing using fast Fourier transforms (FFTs). Additionally, an ambiguous‐cell Doppler correction algorithm is applied to mitigate intercarrier interference (ICI) and resolve velocity ambiguity. This hybrid scheme increases the number of virtual MIMO channels, eliminates distance‐dependent angle errors, and enhances angle estimation accuracy. Furthermore, it overcomes the inherent limitations of standalone RDM or DDM, allowing for adaptive control of unambi guous distance and velocity by adjusting the hybrid ratio. Simulations based on a 77‐GHz 8 × 8 antenna array configuration validate the effectiveness and superior performance of the proposed schemes.
1 January 2017 in Mathematical Problems in Engineering
In order to improve both the transmission data rate and the range resolution simultaneously in integrated radar‐communication (RadCom) systems, orthogonal frequency‐division multiplexing with phase‐coded and stepped‐frequency (OFDM‐PCSF) waveform is proposed. A corresponding high resolution range (HRR) profile generation method is also presented. We first perform OFDM‐PCSF waveform design by combining the intrapulse phase coding with the interpulse stepped‐frequency modulation. We then give the ambiguity function (AF) based on the presented waveforms. Then, the synthetic range profile (SRP) processing to achieve HRR performance is analyzed. Theoretical analysis and simulation results show that the proposed methods can achieve HRR profiles of the targets and high data rate transmissions, while a relative low computational complexity can be achieved.
Stepped-carrier orthogonal frequency division multiplexing (SC-OFDM) radar is an emerging low-cost alternative to standard OFDM radar for automotive applications due to providing high-range resolution at a low sampling rate. However, it is limited by inter-carrier interference (ICI) and velocity ambiguity in high-speed target detection. To address these issues, this paper proposes a two-step method for SC-OFDM radar. The method first applies multi-hypothesis Doppler compensation and leverages peak sidelobe ratio (PSLR) in the range profile as a distinguishing feature to estimate the target’s unambiguous velocity. Then, target signals are reconstructed into components free from ICI. Simulation results confirm the effectiveness of the proposed method. Compared to existing methods, this approach eliminates ICI without repeating OFDM symbols, thereby preserving communication data rate and enhancing suitability for integrated sensing and communication (ISAC) applications.