Thermostats operate alongside intelligent home automation systems for ensuring both the comfort of the occupants as well as the responsible use of energy. The effectiveness of such solutions relies on the ability of the adopted control methodology to respond to changes in the surrounding environment. In this regard, process disturbances such as severe wind or fluctuating ambient temperatures must be taken into account. The present paper proposes a new approach for estimating the heat transfer of residential buildings by employing a lumped parameter thermal analysis model. Various control strategies are adopted and tuned into a virtual environment. The knowledge gained is generalized by means of a long short-term memory (LSTM) neural network. Laboratory scale experiments are provided to prove the given concepts. The results achieved highlight the efficiency of the implemented temperature controller in terms of overshoot and energy consumption.
This study investigates the impact of material and process parameters—specifically, filament color, infill density, and pattern—on the dimensional accuracy of 4D-printed polylactic acid (PLA) objects featuring holes of varying diameters (6, 8, and 10 mm) that undergo a heat-induced recovery process. The objective was to understand how these factors affect shape retention and the dimensional accuracy of holes through a comparative analysis of the diameters before and after recovery. Increased variability in the hole diameters was noted after recovery, regardless of the values of the independent variables. The objects did not fully return to their original planar shape, and the holes did not completely return to their circular form, resulting in smaller diameters for each sample. No significant differences in the hole diameters could be determined. Additionally, there was no consistent trend in identifying the most influential parameter affecting the accuracy of the recovered holes. However, it was observed that higher infill densities improved shape retention. A quasi-static finite elements analysis model was developed to capture the mechanical behavior of the 4D-printed parts. This model incorporated temperature-dependent material characteristics to predict the strain occurring near the holes. Nodal displacements were defined according to the deformed shape. A correlation was established between the observed strains and the post-recovery dimensional accuracy of the specimens. The importance of this work was demonstrated through a case study involving a two-sieve filtering device for small objects.
This study evaluates the feasibility of 3D-printed polymer composite external fixator (EF) rings as a cost-effective alternative to stainless steel fixators, focusing on hybrid fixators for complex tibial fractures. Mechanical performance was assessed in three stages: (1) evaluating the initial EF–tibia configuration under axial loading and wire pre-tension conditions; (2) analyzing the stiffness evolution and weight-bearing capacity during early healing with progressive callus formation; and (3) optimizing ring designs through numerical analysis to improve structural performance under increased pre-tension. The results showed that, for the metallic EF, the axial displacement under one-leg stance reached 8.41 mm without pre-tension, reducing to 6.83 mm at 500 N pre-tension, though transverse displacement remained significant, suggesting the need for higher wire tension. Callus formation enhanced the load-bearing capacity, as expected. However, excessive displacements persisted under the one-leg stance, indicating that full weight-bearing should be delayed beyond two weeks for a fracture gap of 3 mm. A ring design assessment showed that full-ring configurations with two wires per ring improved performance. The 3D-printed full-ring design made of carbon-fiber-reinforced polylactic acid (PLA-CF) reduced stress by 85% at 500 N pre-tension compared to the initial configuration, remaining within allowable limits. While confirming feasibility, the study highlights the need for geometric refinements to accommodate higher preloads and improve transverse stiffness.
This research investigated the feasibility of 3D-printed external fixator (EF) rings made from carbon fiber reinforced polyamide 6 (PA6-CF) as an alternative to the conventional metallic counterpart. The study integrated tensile testing with digital image correlation (DIC) in as-printed and cold plasma-sterilized conditions, finite-element analysis (FEA) under wire loading, topology optimization for material and energy reduction, and evaluation of printability limits for large PA6-CF rings. The average Young’s modulus was 4.76 GPa and the maximum tensile strength was 60.5 MPa for as-printed samples, decreasing by 6.4% and 10.4% after sterilization, respectively. Using these properties as model inputs, FEA predicted safety factors larger than 1.42 for all configurations under 1000 N wire pretension, while topology optimization targeted up to 50% mass reduction without compromising ring stiffness. The study also revealed challenges in the printability of PA6-CF for large and thin components, including dimensional contraction, significant warping and moisture-induced defects, requiring an experienced 3D printer operator.
Wood is a renewable and widely used material whose mechanical performance is strongly influenced by natural defects such as knots, cracks, and resin pockets. These defects affect structural accuracy and make quality assessment an essential step in wood processing and engineering applications. Traditional visual inspection methods are time consuming and subject to individual variability, motivating the development of automated inspection systems based on computer vision. This study proposes a YOLOv8-based framework for automated wood classification and specimen selection. Two YOLOv8 variants, Nano and Medium, were trained on a publicly available wood defect dataset containing more than 20,000 images and over 43,000 annotated defects. The models were used to distinguish defect-free specimens from specimens containing visible defects, enabling objective sample selection. Only specimens classified as defect-free were retained for subsequent three-point bending tests and finite element method (FEM) simulations. Both YOLOv8 models achieved reliable detection performance, allowing consistent separation of defective and defect-free wood samples. The selected specimens exhibited stable mechanical behavior during bending tests, while FEM predictions showed good agreement with the experimental results, with errors below 3.2% in the elastic range. The proposed methodology demonstrates the potential of integrating artificial intelligence, mechanical testing, and numerical simulation into a unified workflow for wood quality assessment and structural evaluation.