Unbound granular materials (UGM) in permeable pavement will experience large numbers of infiltration during their service-life. The frequently changed moisture not only affects the cooling effect of permeable pavement, but also influences the mechanical behaviors of UGM. However, evidence is lacking to state the influence of infiltration on the behaviors of UGM, which is commonly in fully permeable pavement. Considering the influence of infiltration, this study conducted experimental tests to investigate the effect on the water-retaining and bearing capacity of UGM. With the water-retaining tests, the water-retaining rate in the whole structure and at different depths was analyzed under different infiltration numbers and duration. The results showed that the water-retaining rate increased with the extension of the infiltration duration. The infiltration duration had a significant influence on the water-retaining capacity of UGM, while the infiltration number had little. The difference in the water-retaining rate between the top and bottom layers was up to 2.56%. The water-retaining capacity of the integrated structure was hardly affected due to the dissimilarity of the water-retaining rate at different depths. With infiltrations, the fine aggregate in the upside structure migrated downward to the lower structure, resulting in a reduction in water-retaining rate in the upper structure and an increase at the bottom. In addition, the mechanical behaviors were evaluated by the traditional California Bearing Ratio (CBR) and repeated CBR tests under five infiltrations. The first and second infiltration had a significant influence on the CBR of UGM. With two infiltrations, the plastic strain increased by 57.8% via the repeated CBR tests. The resilient strain had an increase by 36.52% and the equivalent modulus decreased by 28.7% with the first infiltration. The first infiltration presented a critical influence on the bearing capacity of UGM and the effect decreased with the increase in the infiltration number. These findings will enrich the behaviors investigation of UGM and promote its application in the fully permeable pavement.

Adequate maintenance and taking active preventive measures can effectively prevent the early disease of asphalt pavements before significant damage occurs. By developing a light screening preventive maintenance agent (LS pre-maintenance agent) for strong ultraviolet (UV) radiation areas, based on the asphalt aging and regeneration mechanism, we analyzed the function and basic components and determined the optimum components ratio based on the best proportion of penetrant and solvent oil for solubility. The optimum ratio for quick-drying and long-term storage ability is the mass ratio of rock asphalt, reducing agent, penetrant, and solvent oil, which is 30:20:20:30. The light-shield agent is 5% of the total mass of the rock asphalt, reducing agent, penetrant, and solvent oil, and the dispersant is 0.4%. Digital image technology was used to provide an accurate measurement of the LS pre-maintenance agent penetration depth, evaluate its permeability and reasonable amount. We then used the rolling thin film oven test (RTFOT) to analyze its effect on aged asphalt and evaluated the restoration performance. Using the strong UV radiation aging test, we analyzed its anti-light aging performance. The results showed that pavement must be closed at least 2 h after the brushing LS pre-maintenance agent has been applied and this can be extended to upwards of 8 h time permitting. A dosage of 0.5 kg/m² can ensure sufficient penetration depth and curing effect. Furthermore, the agent shows excellent restorative and anti-light aging abilities, which can effectively improve the low-temperature performance of aged asphalt and meet the pre-maintenance requirements for asphalt pavement, especially in strong UV radiation areas.

The constitutive model is the crucial part for the finite element analyses. To study the elasto-plastic properties of unbound granular materials (UGMs) under repeated vehicular loads, an elasto-plastic constitutive model called revised spatially mobilized plane (SMP) was proposed and validated. In this study, the revised SMP model was used for the plastic strain analyses of a typical three-layer pavement structure. To make comparisons, the Mohr-Coulomb and Druck-Prager models were employed for the numerical computation. The results show that plastic tensile and compressive strains in the horizontal and vertical directions appear on the top surface of UGM using the revised SMP model, but no plastic strains are produced by the Mohr-Coulomb and Druck-Prager models. The distribution of plastic strains in the revised SMP model had a good relationship with the actual loading areas under the vehicular loading, which related to the rutting. With the Mohr-Coulomb and Druck-Prage models, a great plastic strain was produced during the first several loading cycles and hardly increased in the following loading cycles, while the plastic strain in the revised SMP model presented an obvious increasing tendency with increased loading cycles. The predicted permanent deformations of the revised SMP, Mohr-Coulomb and Druck-Prage models were 0.557 mm, 0.78 mm and 0.155 mm, respectively. Our work reveals that the Mohr-Coulomb model may over-predict and Druck-Prage model may under-predict the rutting of pavement in early loading stage and the results proved that the revised SMP model had advantages in the description of the plastic strain of UMG under repeated loads.