Jingpeng JIA

Dr. Jingpeng JIA


Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 April 2025 in Coatings
Verified
Journal Article
Open access
PDF file
SPSimiao Pan
Simiao Pan
XLXiang Liu
Xiang Liu
XLXiaolong Li
Xiaolong Li
JJJingpeng JIA
Jingpeng JIA
JYJun Yang
Jun Yang
Polyphosphoric acid (PPA), a chemical modifier widely used in petroleum asphalt, results in significant performance improvements. However, its effectiveness for modified emulsified asphalt has not yet been thoroughly verified. This study aims to investigate the emulsification properties, rheological characteristics, compatibility, and modification mechanisms of PPA-modified emulsified asphalt and validate the feasibility of applying PPA for modification. Initially, PPA-modified emulsified asphalt was prepared at different dosages (0%, 0.5%, 1.0%, 1.5%, and 2.0%), and its emulsification characteristics, including evaporation residue properties and storage stability, were evaluated. Subsequently, the rheological performance and compatibility of PPA-modified emulsified asphalt at various temperatures were evaluated using a dynamic shear rheometer. Finally, Fourier transform infrared spectroscopy (FTIR) and fluorescence microscopy (FM) were utilized to investigate the effects of PPA modification on the chemical composition and microscopic characteristics of emulsified asphalt. The results indicated that, with increasing PPA dosage, the softening point of modified emulsified asphalt initially decreased and then increased, while penetration and ductility first increased and then decreased, accompanied by reduced storage stability. Furthermore, PPA modification can enhance the high-temperature stability, fatigue properties, and low-temperature performance of emulsified asphalt, but the effectiveness depended on the dosage of PPA. Specifically, optimal compatibility of modified emulsified asphalt was achieved at a PPA dosage of 1.0%. Notably, PPA underwent hydrolysis within the emulsified asphalt system, leading to modification mechanisms distinct from those observed in base asphalt modification. At a PPA dosage of 1.0%, asphalt particles within the emulsified asphalt exhibited the most uniform distribution. Conversely, excessive PPA dosage (e.g., 2.0%) caused significant particle aggregation, consequently weakening the modification effect.

22 September 2025 in Materials
Verified
Journal Article
Open access
PDF file
ZQZhen Qin
Zhen Qin
XLXiang Liu
Xiang Liu
ZSZHENG Shaopeng
ZHENG Shaopeng
SPSimiao Pan
Simiao Pan
XLXiaolong Li
Xiaolong Li
HXHang Xiong
Hang Xiong
High-permeability emulsified asphalt has emerged as a promising prime coat for enhancing interlayer bonding in semi-rigid pavement structures. However, its widespread adoption remains limited by insufficient permeability and inconsistent mechanical properties. This study systematically investigated the effects of emulsifier ionic type (cationic or anionic), kerosene dosage (0–20%), and diluted asphalt content (corresponding to oil-water ratios of 5:5 and 4:6) on the comprehensive performance of high-permeability emulsified asphalt. Fundamental physical tests (sieve residue, evaporation residue, penetration, softening point, ductility), permeability evaluation, rotational viscosity measurements, and adhesion performance tests were conducted. Grey relational analysis (GRA) was employed to quantify the influence of each factor and their interactions on key performance metrics. The results reveal that anionic emulsifiers significantly improved low-temperature ductility and permeability. A low kerosene dosage (<10%) enhanced permeability and viscosity but compromised thermal stability at higher levels. Reducing the diluted asphalt content partially offset these adverse effects. GRA identified kerosene dosage as the dominant factor influencing permeability, softening point, and adhesion performance while emulsifier ionic type primarily affected ductility, and oil-water ratio strongly governed emulsification quality and viscosity. These findings provide quantitative insights for optimizing the composition of high-permeability emulsified asphalt and serve as a theoretical foundation for its engineering application in durable prime coats.

19 September 2025 in Coatings
Verified
Journal Article
Open access
PDF file
TSTao Shen
Tao Shen
ZSZHENG Shaopeng
ZHENG Shaopeng
XLXiang Liu
Xiang Liu
XLXiaolong Li
Xiaolong Li
JJJingpeng JIA
Jingpeng JIA
TSTao Shen
Tao Shen
Microorganisms present in asphalt pavement service environments can alter the composition of asphalt through metabolic activities, thereby affecting its rheological properties. To investigate this influence and compare performance variations across asphalt types, two asphalt-degrading bacterial strains were isolated from in-service pavements. Following 16S rRNA gene sequencing and phylogenetic analysis, the strains were identified as Pseudomonas putida and a putative novel species within the Citrobacter genus. Using a custom-designed thin-film inoculation system, the performance evolution of base asphalt and styrene-butadiene-styrene (SBS) modified asphalt was systematically evaluated after microbial activity periods of 5, 10, and 15 days. Conventional property tests and multi-temperature rheological analyses (temperature sweep, multiple stress creep recovery test, linear amplitude sweep, 4 mm DSR) were conducted. Results demonstrated that microbial action reduced penetration, elevated softening point, and decreased ductility in both asphalt types, with more pronounced changes observed in base asphalt. High-temperature rheological parameters (G*/sinδ), recovery rate, and non-recoverable creep compliance indicated compromised resistance to permanent deformation. SBS-modified asphalt substantially mitigated these detrimental effects. Fatigue life of base asphalt decreased overall with periodic fluctuations, whereas SBS-modified asphalt exhibited superior fatigue stability: after an initial decline at 5 days, performance recovered and stabilized between 10 and 15 days. Low-temperature performance showed slight improvement in base asphalt, while SBS-modified asphalt demonstrated significant enhancement during later activity stages.