Oil refining encompasses a series of unit operations designed to fractionate crude oil streams to yield higher-value products. Distillation, a pivotal process, involves a cascade of units integrated within a distillation column, facilitating the concurrent transfer of mass and heat between the liquid and vapor phases while maintaining thermodynamic equilibrium between these phases. In this study, we conducted numerical simulations and optimization of an atmospheric distillation column, establishing parametric relationships that furnish insights into operational performance and the overall process. This becomes especially crucial when assessing key parameters such as feed flow rate, temperature, steam injection rates, reflux conditions, and side stream flow rates. The results obtained from the optimization process showcase its effectiveness in maximizing the objective function, ensuring a daily diesel production rate of 2,900.00 metric tons, which represents an approximately threefold increase compared to industrial production levels prior to unit optimization. In this context, it is evident that sustaining optimal industrial performance in these processes necessitates the continual enhancement of operational conditions, rooted in simulation and optimization studies of refining columns.
To define how sustainable a method is in relation to othfiers, it is necessary to measure them numerically. This includes the creation of management models that create a link between the concept of creating value for the business with ecological and social compatibility. Sustainable production systems must comply with a series of principles and good practices in light of the Triple Bottom Lines concept. Therefore, the objective of this article is to compare and measure, focusing on the triple bottom line, different metal cutting operations used in the industry. To this end, a methodology was developed that simultaneously considers economic, social and environmental parameters. In total, thirteen variables were measured for each of the following metal cutting operations: band saw, oxyfuel, plasma, abrasive waterjet and laser cutting. This research also evaluated the surface finish of the parts obtained after the cutting operation. The main results show that the laser cutting process presented the greatest gain and the longest time for the operator, but with the worst finish. The plasma cutting process had the highest noise level and the highest tool cost. Continuous cutting with a band saw was the process that presented the greatest sustainability and best finish.
The energy efficiency of wind turbines is essential for sustainable energy generation. Therefore, the objective was to evaluate the design and performance of a Savonius turbine, to provide recommendations to optimize its efficiency and power generation capacity in different wind conditions. To address the problem, the energy available to the turbine is analyzed and the concept of the Betz limit is introduced as a reference point for the conversion efficiency. The relationship between wind speed, power coefficient and torque coefficient, fundamental to understanding turbine performance, is examined. Furthermore, the influence of tip speed ratio (TSR) on power extraction is studied, and the torque coefficient is defined as a key performance measure. Experimental tests are carried out in a wind tunnel to evaluate the structural and performance characteristics of the Savonius wind turbine. The results show a correlation between wind speed and turbine performance, with the torque coefficient as the main indicator of efficiency. The presence of guide blades on the Savonius wind turbine can increase the power generated but can decrease the power and torque coefficients. Guide vanes can increase wind speed and electrical energy production, but they can also reduce efficiency by creating a barrier that affects energy capture. Therefore, their use must be carefully evaluated to optimize power production and system efficiency, considering performance objectives and installation site conditions.
This article delves into transport phenomena, essential in science and engineering research, emphasizing Matano's Interface as a key element in diffusion studies. The primary goal is to elucidate a graphical procedure for approaching Matano's Interface within diffusion couples, aiming to calculate diffusion coefficients across various compositions. The comprehensive exploration of the Boltzmann-Matano method, particularly focusing on concentration-dependent diffusion coefficients, is accentuated. Acknowledging the historical context of Ludwig Boltzmann and Matano, the article highlights the practical application of their methodologies, notably in an annealed copper-zinc couple. The graphical determination of the Boltzmann-Matano interface proves crucial in understanding diffusion dynamics. The article successfully integrates theoretical understanding with practical insights, contributing to the broader field of transport phenomena research in science and engineering.
3 January 2025 in The Journal of Engineering and Exact Sciences
This study investigates the effect of laser texturing on carbide inserts in the milling of vermicular cast iron, commonly used in high-speed train brake disc manufacturing. The objective was to evaluate the performance of laser-textured tools compared to blast-textured ones, applying different coatings (TiAlN-Futura®, AlCrN-Alcrona® and AlCrN-Helica®). Life tests were conducted under various cutting conditions, including cutting speed, depth of cut, and feed per tooth, without the influence of cutting fluids. The results demonstrated that laser-textured tools removed significantly higher volumes of material than blast-textured tools. Cutting speed and depth of cut were the most influential parameters on tool life, with cutting speed showing statistical significance across all tools. The TiAlN-Futura® and AlCrN-Helica® coatings proved to be the most efficient under the tested conditions. The study concludes that laser texturing is a viable alternative to conventional blasting for enhancing tool performance in the milling of vermicular cast iron.