Yufei Li

Dr. Yufei Li


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2024 in Coatings
Verified
Journal Article
Open access
PDF file
YLYufei Li
Yufei Li
LLLinghao Li
Linghao Li
WLWenzhe Li
Wenzhe Li
LLLinfeng Lu
Linfeng Lu
LTLu Tian
Lu Tian
WTWeidong Tian
Weidong Tian
Nickel–tungsten (Ni-W) alloys are gaining significant attention due to their superior hardness, wear resistance, anti-corrosion and electrochemical hydrogen evolution reaction (HER) activity. In this work, porous and crack Ni-W alloys with different W contents were prepared in a pyrophosphate bath. The key to forming a porous structure is a very high current density over 300 mA cm−2. The HER activity of porous and crack Ni-W alloys was studied by means of electrochemical technologies of linear sweep voltammetry (LSV), Tafel curves (Taf) and electrochemical impedance spectroscopy (EIS). Compared with the crack Ni-W alloy, the porous Ni-W alloy exhibits improved alkaline electrochemical HER performances, which can deliver a current density of 10 mA cm−2 at 166 mV (η10) vs. RHE (reversible hydrogen electrode).

30 April 2024 in Processes
Verified
Journal Article
Open access
PDF file
YLYufei Li
Yufei Li
DZDajiang Zhu
Dajiang Zhu
JYJian Yang
Jian Yang
QLQiang Liu
Qiang Liu
LZLin Zhang
Lin Zhang
SWShuai Wang
Shuai Wang
We aimed to investigate the corrosion patterns and the main controlling factors of N80 steel and P110 steel tubing under different sections. Conducting weight loss corrosion experiments for 168 h using high-temperature and high-pressure autoclaves to simulate the corrosion behavior of two types of casing materials, N80 steel and P110 steel, in different well sections under specific conditions of CO2 content, chloride ion concentration, temperature, pressure, and sulfate-reducing bacteria population in highly mineralized formation water. X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS) were used to analyze the corrosion products, surface morphology, and elemental composition of the two steel pipes. Additionally, 3D microscopy was employed to observe the morphology and measure the dimensions of localized corrosion pits. Under different well sections, the corrosion products formed on N80 steel and P110 steel mainly consist of FeCO3, and crystalline salts of chlorides present in the solution medium. Under low-water-cut conditions, narrow and deep corrosion defects were observed, while narrow and shallow corrosion defects were found under high-water-cut conditions. In the upper wellbore section, both steel pipes exhibited dispersed and thin corrosion product films that suffered from rupture and detachment, resulting in severe localized corrosion. In the middle wellbore section, the corrosion product film on N80 steel comprised irregularly arranged polygonal grains, some of which exhibited significant gaps, leading to extremely severe corrosion. For P110 steel, the corrosion product film was also dispersed and thin, with extensive detachment and extremely severe corrosion. In the lower wellbore section, both steel pipes were covered with a dense layer of grains, with smaller gaps between them, effectively protecting the metal matrix from corrosion. Consequently, the corrosion rate decreased compared to the middle section but still exhibited severe corrosion. In low-water-cut conditions, attention should be given to the risk of column safety due to corrosion from condensate water and CO2, as well as the size of narrow and deep corrosion defects in the middle wellbore section. In high-water-cut conditions, it is recommended to use corrosion inhibitors in combination while focusing on SRB bacteria corrosion in the upper wellbore section, condensate water in the middle section, CO2 content and chloride ion coupling in the lower section, and the size of narrow and shallow corrosion defects causing column safety risks.

5 June 2026 in Processes
Verified
Journal Article
Open access
PDF file
YFYukun Fu
Yukun Fu
JYJian Yang
Jian Yang
YLYufei Li
Yufei Li
YZYidan Zhang
Yidan Zhang
XWXingming Wang
Xingming Wang
JXJingyang Xu
Jingyang Xu
In complex wellbore environments, traditional ball-drop, cable, and electromagnetic sliding sleeve communication methods face reliability problems caused by high temperature, high pressure, complex trajectories, and signal attenuation. This paper presents a pressure-wave-based downhole communication and sliding sleeve activation system. Surface pressure variations generated by pump displacement and pressure relief are used to transmit encoded commands through the wellbore fluid and realize non-contact activation of the downhole sliding sleeve. A wellbore pressure-wave propagation model is established, and the effects of well depth, wellbore diameter, pump displacement, pump-on time, pressure-relief timing, and pressure-relief duration on bottom-hole pressure response are analyzed. A bipolar non-return-to-zero coding strategy combined with a constant-threshold decoding method is proposed to improve signal recognizability and robustness. Simulation results show that for a 5000 m wellbore and a pressure-wave velocity of 1100–1300 m/s, the signal transmission delay is approximately 4.2 s, and the bottom-hole pressure responses induced by pump displacement and pressure-relief valve operation can be clearly distinguished. Laboratory tests at 150 °C and 120 MPa showed that the sliding sleeve achieved a 110 mm stroke and 100% opening ratio in four repeated activation tests. In the field test, three pressure command cycles between 10 MPa and 40 MPa successfully triggered the sliding sleeve, followed by a squeeze test with a displacement of 0.3–0.7 m3/min and a maximum pressure of approximately 60 MPa. The results demonstrate that the proposed system provides a feasible and reliable pressure-wave communication method for downhole sliding sleeve activation in deep and long horizontal wells.

5 November 2025 in Processes
Verified
Journal Article
Open access
PDF file
NZNaiyan Zhang
Naiyan Zhang
YLYufei Li
Yufei Li
GTGeng Tang
Geng Tang
HGHao Gong
Hao Gong
DZDajiang Zhu
Dajiang Zhu
QHQiyao He
Qiyao He
In high-sulfur environments, the failure risk of completion tubing increases due to the coupling effect of mechanical and electrochemical corrosion during the acidification production process. The corrosion behavior of P110SS tubing steel was investigated by an HTHP corrosion weight loss experiment and an electrochemical corrosion experiment. Scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) were used to analyze the surface morphology of the corrosion products. In addition, a prediction model for the remaining service life of completion tubing under the synergistic effect of corrosion and stress was established during the acidification production process. The results show that acidification operations have a significant impact on the subsequent service life of tubing; the corrosion rate of P110SS tubing in the full acidification production process is much higher than that after the produced gas field solution corrosion treatment alone. Obvious pitting marks, micropores, and microchannels are observed in the corrosion product film of P110SS steel after acidification treatment, and the corrosion product film structure of P110SS steel is loose and honeycomb-like after acidification production treatment. The corrosion products are mainly FexSy and FeCO3 after acidification production corrosion treatment. The corrosion during the acidification production stage is controlled by cathodic polarization. The remaining service life of tubing after production corrosion treatment can reach up to 29 years, while the remaining service life of tubing after acidification production corrosion treatment is significantly reduced, with a maximum of only 8 years. The research results have guiding significance for the selection, optimization, and design of high-sulfur-gas well tubing.

29 October 2025 in Processes
Verified
Journal Article
Open access
PDF file
WLWenzhe Li
Wenzhe Li
YLYufei Li
Yufei Li
KZKui Zhang
Kui Zhang
HGHao Gong
Hao Gong
NZNaiyan Zhang
Naiyan Zhang
JSJunlin Su
Junlin Su
Under long-term high-temperature and static conditions, high-density workover fluid settles, increasing the risks of workover operations. In order to achieve a quantitative assessment of the sedimentation stability of oil well workover fluids, this study adopted spectral analysis to conduct stability tests on water dispersions of barite with different concentrations. Meanwhile, a comprehensive assessment was conducted on the sedimentation rate of the well repair fluid, the size of solid particles and the changes in the thickness of the sedimentary layer in 1# Well, 2# Well and 3# Well. With the increase in barite concentration, its sedimentation behavior changes from free sedimentation at low concentrations to flocculation sedimentation at high concentrations, and the sedimentation rate shows a slowing trend. The increase in sedimentation rate is positively correlated with the increase in density, and the intensity of the initial backscattered light at the bottom of the well also increases accordingly. In addition, during the sedimentation process of sediment, the variation pattern of particle velocity shows the characteristics of being relatively fast in the early stage and gradually accelerating in the middle and later stages. The results show that the average particle size of barite solution is 4.93 μm, and the average particle size of the three workover fluids is 87.5 μm. The deposition thickness range of barite solution is 5–50 mm, and that of the three workover fluids is 25–51.58 mm. It provides data support for the rapid quantitative evaluation of the long-term stability of oil well workover fluids.