Modern trends in improving environmental safety have determined the urgency in creating innovative technologies that allow the production of electricity and hydrogen without the emission of harmful substances. However, at the moment, there are not so many technical solutions offering the combined production of these useful products with a high degree of efficiency and environmental friendliness. The transition to oxy-fuel combustion power cycles for the co-production of electricity and hydrogen is a prospective way to decrease carbon dioxide emissions into the atmosphere from the energy sector. To achieve zero emissions, the semi-closed oxy-fuel combustion cycle is combined with a steam methane reformer, which has a high energy efficiency through reducing losses in the steam turbine condenser. The modeling methodology has been described in detail, including the approaches to defining the working fluid properties and mathematical models of the different steam methane reforming plants and the oxy-fuel combustion power plant. According to the results of the thermodynamic analysis of the steam methane reforming plant, it was found that an increase in the temperature from 850 to 1000 °C leads to a decrease in the mass flow fuel by 16.3% due to the shift towards a direct reaction. Moreover, the optimal temperature in the reformer lies in the range of 900–950 °C. A comparison of the energetic and ecological characteristics of various steam methane reformer units showed that the scheme with oxy-fuel combustion is better compared to the scheme with CO2 capture by absorption in monoethanolamine; the efficiency is 6.9% higher and emissions of carbon dioxide are 22 times lower. According to the results of the thermodynamic analysis of a novel oxy-fuel combustion power cycle, it was found that its performance varied regarding the range of electricity production (123.6–370 MW) and hydrogen production (0–10.8 kg/s). The efficiency of the oxy-fuel combustion power cycle varies in the range of 47.2–70.1%. Based on the results of the operation regimes analysis, the energy complex performance map has been developed, allowing identification of the efficiency and working fluid massflow by net power and produced hydrogen massflow.
Increasing the efficiency and capacity of nuclear power units is a promising direction for the development of power generation systems. Unlike thermal power plants, nuclear power plants operate at relatively low temperatures of the steam working fluid. Due to this, the thermodynamic efficiency of such schemes remains relatively low today. The temperature of steam and the efficiency of nuclear power units can be increased by integrating external superheating of the working fluid into the schemes of steam turbine plants. This paper presents the results of a thermodynamic analysis of thermal schemes of NPPs integrated with hydrocarbon-fueled plants. Schemes with a remote combustion chamber, a boiler unit and a gas turbine plant are considered. It has been established that superheating fresh steam after the steam generator is an effective superheating solution due to the utilization of heat from the exhaust gases of the GTU using an afterburner. Furthermore, there is a partial replacement of high- and low-pressure heaters in the regeneration system, with gas heaters for condensate and steam superheating after the steam generator for water-cooled and liquid-metal reactor types. An increase in the net efficiency of the hybrid NPP is observed by 8.49 and 5.11%, respectively, while the net electric power increases by 93.3 and 76.7%.
19 October 2026 in Clean Energy Science and Technology
The oxy-fuel combustion power cycle (OFPC) based on the Allam cycle with supercritical carbon dioxide is a promising technology for reducing greenhouse gas emissions. While current literature estimates its efficiency with natural gas between 48% and 62%, the impact of the power unit's electrical power capacity on overall efficiency remains underexplored. This study investigates how supplied power affects OFPC net efficiency through preliminary thermodynamic parameter optimization. A comprehensive mathematical model of the OFPC was developed using the Aspen software package. The model integrates key subsystems: a gas turbine unit, cooler-separator, air separation unit, and compressor-storage unit. The modeling results indicate that lowering the working fluid temperature at the cooler-separator outlet to 17 °C boosts the maximum net cycle efficiency to between 51.16% and 53.1%, assuming complete moisture removal in the cooler-separator. Furthermore, a quantitative assessment of the scale effect shows significant benefits from increasing capacity. Scaling the supplied capacity from 50 MW to 800 MW reduces the specific electricity consumption for auxiliary power needs by 37.6%, achieving 1.12 kW/kg O2. In conclusion, utilizing higher-capacity equipment in the OFPC is both technologically and energetically justified. Increasing the supplied capacity from 50 MW to 800 MW effectively increases the overall net efficiency of the Allam cycle by 1.97%.