There is an increased accessibility of over-the-counter (OTC) whitening agents with very little data in the literature regarding their effectiveness. This review was done to determine their effectiveness of the predominant OTC whitening agents from 2006 until 2018 where a comparison of each agent was made with a placebo, no treatment or with other OTC whitening agents. The major categories of OTC whitening agents such as dentifrices, whitening strips and paint on gels. Dentist prescribed bleaching applied at home and in-office bleaching studies and studies that demonstrated whitening products to participants were excluded. Articles were searched for in the databases of Medline (Ovid), PubMed, the Cochrane Library and Cochrane Central Register of Controlled Trials. Twenty-four articles were included in the systematic review and the quality of studies was determined by the GRADE (Grading of Recommendations, Assessment, Development and Evaluations) ranking criteria. Compared to other OTC, strips are reported to be effective. Two studies determined whitening strips to be effective. Whitening strips have been shown to be effective when compared with placebos and other OTC whitening agents. Dentifrices are effective in changing the shade of the tooth “by removing extrinsic stains” when compared to a placebo and non-whitening dentifrices, but they are not as effective in comparison to whitening strips. There is a lack of evidence with regards to the effectiveness of paint-on gels. While there is some evidence that OTC can alter shade in the short term, there is a need for better-designed studies.
The purpose of this systematic review was to investigate how different interventions can impact the bond strength of additively manufactured crown materials after cementation. Four online databases Ovid MEDLINE, Scopus, Web of Science and Google Scholar were searched up to January 2023. Inclusion criteria were English-language publications, full-text, and in vitro studies only. Exclusion criteria were studies that did not assess the bonding of an additively manufactured crown material to cement or did not conduct any bond strength tests. An assessment of risk of bias was done in accordance with a modified Consolidated Standards of Reporting Trials (CONSORT) checklist. Each study was analysed and compared based on the interventions and bond strength results. Six studies satisfied the inclusion and exclusion criteria, five of which evaluated photopolymerised resin and one that tested zirconia manufacturing via 3D printing. All studies observed a low risk of bias. The interventions applied included the type of surface pretreatments, airborne-particle abrasion pressure, cement type, taper of crown, and artificial aging. Three studies compared the bonding performance to milled materials. The bond strength of crown materials additively manufactured from photopolymers presented high values and are comparable to milled materials. The systematic review demonstrated there was no definite superior cement type, but airborne-particle abrasion with alumina was generally recommended. There is a clear gap in the literature regarding the bond strength of additively manufactured crowns. Therefore, further research is necessary to evaluate its clinical applicability for permanent restorations. Factors influencing the bond strength of additively manufactured crown materials should be evaluated so dental professionals can adopt procedures that promote the strongest bond.
30 April 2013 in International Journal of Dentistry
Purpose. This in vitro study investigates how unilateral and bilateral occlusal loads are transferred to an implant assisted removable partial denture (IARPD).Materials and Methods. A duplicate model of a Kennedy class I edentulous mandibular arch was made and then a conventional removable partial denture (RPD) fabricated. Two Straumann implants were placed in the second molar region, and the prosthesis was modified to accommodate implant retained ball attachments. Strain gages were incorporated into the fitting surface of both the framework and acrylic to measure microstrain (μStrain). The IARPD was loaded to 120Ns unilaterally and bilaterally in three different loading positions. Statistical analysis was carried out using SPSS version 18.0 (SPSS, Inc., Chicago, IL, USA) with an alpha level of 0.05 to compare the maximumμStrain values of the different loading conditions.Results. During unilateral and bilateral loading the maximumμStrain was predominantly observed in a buccal direction. As the load was moved anteriorly theμStrain increased in the mesial area. Unilateral loading resulted in a twisting of the structure and generated a strain mismatch between the metal and acrylic surfaces.Conclusions. Unilateral loading created lateral and vertical displacement of the IARPD. The curvature of the dental arch resulted in a twisting action which intensified as the unilateral load was moved anteriorly.