This paper proposed a fast modularized multiwinding transformer balancing topology (MMTBT) for series-connected supercapacitors. With the proposed topology, the voltage balancing control inside modules and between modules is completely decoupled and the degree of modularization is high. The control inside different modules is independent, while with the existing MMTBT different modules share the same PWM drive. With the proposed topology, the variable frequency control strategy can be used to realize a fast balancing speed. With the proposed balancing topology, the balancing between modules is realized by discharging the higher voltage modules. The MMTBT of the higher voltage modules will act as a fly-back converter and the excitation current is in continuous current mode (CCM) to realize a big discharging power. The higher voltage module will be discharged with a big discharging power, then the balancing speed between modules will be fast. The fast balancing speed is realized inside modules and between modules, then the balancing speed of the whole balancing system will be fast. The variable frequency control strategy as well as the control strategy of boost converter are analyzed in detail and the excellent performance of proposed balancing topology is proved by experimental results.
There is a significant positive proportional correlation between the condition of ethylene propylene diene monomer (EPDM) insulation and partial discharge (PD) characteristics in electric multiple units (EMUs) cable termination. Especially for the cable terminations with long service life, the aging effect of EPDM insulation material is significant due to long-term high-current load. In this article, electrical deterioration and PD development of EPDM insulation under long-term thermal degradation is conducted. During the test process, the phase-resolved PD (PRPD) analysis, PD inception voltage (PDIV), physicochemical properties, and flashover voltage of EPDM samples with different thermal degradation are measured. The relationship between the thermal degradation extent of EPDM insulation and PD characteristics is also proposed. The results show that electrical deterioration of the aged sample can be divided into four gradations by PD amplitude and pulse repetition rate. In the four gradations, the shape of the PRPD spectrum in every gradation changes significantly with different thermal degradations. Surface morphologies of EPDM insulation show different features such as gully areas and white particles. The results of the Fourier transform infrared (FTIR) spectroscopy test indicate that the increase of oxygen-containing groups and free radicals are the key reasons for the rapid PD development process of cable insulation under different electrical gradations and thermal-oxygen degradations.
In order to reduce the current ripple and improve the power density of the system, the multiple structure design is generally adopted by the traditional bidirectional DC/DC converter. However, the fixed multiplicity design can’t make the DC/DC power converter always output the smallest current ripple under different duty ratios. Through this research, it is found that the current ripple is related to duty cycle and parallel multiplicity, and then a variable multiplicity bidirectional DC/DC power converter is proposed. Firstly, the relationship between the current ripple and parallel multiplicity and duty cycle is deduced, and the basic topology of variable multiplicity bidirectional DC/DC power converter is determined; Secondly, the average value model and AC small signal model of the system are established based on the topological structure, and then the state equation is obtained. Thirdly, the current compensation control method is designed based on the state equation. Finally, the experimental platform of variable multiplicity bidirectional DC/DC power converter is built.
22 May 2024 in IEEE Transactions on Power Electronics
The electrochemical impedance is a powerful tool to characterize battery state, and online measurement of battery impedance has significant importance. In this letter, an online battery impedance measurement method based on second-order generalized integrator (SOGI) and equivalent reactive current injection technology is proposed. An equivalent reactive current is injected to battery, which does not consume energy theoretically, thus amplitude of the excitation current can be set with a large value, then the signal-to-noise ratio is high and no additional power supply is required for the current injection. The SOGI is used to extract the battery impedance, which can be digitized implementation by microcontroller unit. Thanks to the bandpass characteristics of SOGI-based filters, the voltage and current signals with the injected frequency are only extracted and this will result in high accuracy. By using SOGI-based filters replaces the classic low-pass filters, the measurement time is reduced and the filtering effect is improved. The proposed method is analyzed in detail, and the experiment results with different loads and different batteries and excitation signal frequencies are presented. The experimental results indicate that the proposed method is correct and effective.