Film cooling, a vital method for controlling surface temperatures in components subjected to intense heat, strives to enhance efficiency through innovative technological advancements. Over the last several decades, considerable advancements have been made in film cooling technologies for applications such as liquid rocket engines, combustion chambers, nozzle sections, gas turbine components, and hypersonic vehicles, all of which operate under extreme temperatures. This review presents an in-depth investigation of film cooling, its applications, and its key mechanisms and performance characteristics. The review also explores design optimization for combustion chamber components and examines the role of gaseous film cooling in nozzle systems, supported by experimental and numerical validation. Gas turbine cooling relies on integrated methods, including internal and external cooling, material selection, and coolant treatment to prevent overheating. Notably, the cross-flow jet in blade cooling improves heat transfer and reduces thermal fatigue. Film cooling is an indispensable technique for addressing the challenges of high-speed and hypersonic flight, aided by cutting-edge injection methods and advanced transpiration coolants. Special attention is given to factors influencing film cooling performance, as well as state-of-the-art developments in the field. The challenges related to film cooling are reviewed and presented, along with the difficulties in resolving them. Suggestions for addressing these problems in future research are also provided.
The impact of a drop on a solid surface has been studied for many years. However, most of the previous numerical simulations were focused on the drop impact on a surface at room temperature and standard atmospheric pressure. This paper presents a numerical study of n-heptane and n-decane drops impacting solid surfaces with the consideration of high temperature and high pressure using smoothed particle hydrodynamics (SPH). The SPH method is validated against experiments from our work and literature. This work is focused on two typical drop-impact regimes, namely, spread and rebound. Different drop impact sequences were simulated at the wall temperature in the range of 27–400 °C and the ambient pressure between 1–20 bars. The difference between the inception of film boiling and liquid saturation temperature was found to decrease with elevating ambient pressure. The spread factor and apex height are investigated for the regime of spread. The results indicate that the lower viscosity fluid has a smaller spread factor as compared to the fluid with higher viscosity. The variation of Leidenfrost temperature with ambient pressure for both n-heptane and n-decane droplets is established numerically and compared with the trend observed in the experiment. The simulation outcomes of drop rebound for high boiling point liquid (n-decane) in the film boiling regime at atmospheric pressure show that with the increasing wall temperature, the drop rebound height and vapor layer height increase. Finally, the effect of ambient pressure on drop rebound height and velocity is investigated. The numerical results indicate that the increase in ambient pressure reduces the droplet rebound velocity and rebound height.
In this paper, we propose and demonstrate a highly sensitive Microbend Fiber Sensor (MFS) for Ballistocardiogram (BCG) recording. The MFS based BCG sensor is built into a cushion. It is a portable, small, light and low cost device. High quality and repeatable BCG signals can be obtained by using this device which allows patients at home to monitor their cardiovascular health. The measured BCG waveforms closely resemble those in the existing literatures. The BCG heart beat detection agrees well with one from photo-plethysmography (PPG) signal.
The smoothed particle hydrodynamics (SPH) method has been increasingly applied to simulate multiphase flows with large density ratios, but the method is computationally expensive when a high resolution is needed. Traditionally a uniform spatial resolution (USR) is used in an SPH simulation. In our previous work, an adaptive spatial resolution (ASR) method was developed for use in the SPH simulations of multiphase flows; the spatial resolution changes adaptively according to the distance to the interface between different phases. In this paper, the SPH-ASR method for multiphase flows is improved by introducing a particle shifting technique to improve the distribution of particles. This particle shifting technique considers the variable smoothing length. The present SPH-ASR method is further enhanced by optimizing the algorithm for adaptive resolution. In addition, the current SPH-ASR method is extended from two- to three-dimensional applications. The improved SPH-ASR method is validated by simulating the dam-break flows, liquid drop formation, and drop impact on a solid surface. Results show that the present SPH-ASR method can greatly reduce the computational cost while maintain the same accuracy to the uniform resolutions.
This paper presents a numerical study of a pair of water drops simultaneously and non-simultaneously impacting on a heated surface using smoothed particle hydrodynamics (SPH). The present SPH method is validated qualitatively and quantitively with available experiment results for the impact of single, simultaneous, and non-simultaneous drops on the solid surface. Numerical simulations are performed at the Weber number in the range of 20–117, surface temperature in the range of 25–250 °C, and pressure in the range of 1–20 bar. In the simulations, the coalescence, breakup, and evaporation of the drops are considered. After the collision of the two drops, the hydrodynamic behavior of the uprising sheet height and spreading areas are investigated by considering the horizontal and vertical distances between the two drops, Weber number, surface temperature, and elevated pressure. The numerical results indicate that the Weber number and horizontal distance significantly influence the height of the rising sheet and the spreading area. Conversely, the vertical spacing does not affect the rising sheet height or spreading area. The drop rebound height increases with the wall temperature in the film boiling regime for high boiling point liquids at atmospheric pressure. The effect of ambient pressure on drop rebound height is investigated for simultaneous and non-simultaneous impacts. According to the numerical results, the pressure increase causes a decrease in droplet rebound height.
1 June 2022 in Engineering Analysis with Boundary Elements