Magnetization vector inversion (MVI) is an effective method for simultaneously determining the distribution of magnetization intensity and direction without knowing the direction of magnetization beforehand. Nevertheless, the presence of serious non-uniqueness in MVI imposes challenges in achieving accurate and reliable results. To improve the accuracy of MVI, we propose a method that incorporates a modulus constraint, informed by an analysis of the model constraints in two different frameworks. We employ a sparse operator on the magnetization magnitude and obtain an explicit expression for the magnetization components, establishing correlation constraints among them. Synthetic test results show that this method can achieve models with clear boundaries and consistent magnetization directions. Furthermore, the application of a sparse operator to the gradient’s modulus of the magnetization magnitude helps recover inclined structures. However, the dispersed magnetization directions suggest that we should also constrain the magnetization direction, simultaneously. The inversion of magnetic data measured over the Zaohuohexi iron-polymetallic deposit in Qinghai Province, northwest China, verified the proposed approach’s effectiveness.
To better understand the geothermal system of the Gonghe Basin, we deployed 471 magnetotelluric survey points with an average distance of 2~3 km, covering the eastern and southern areas of the Basin. We used ModEM inversion software to carry out 3D inversion of 431 survey points and established a 3D-electrical model at a depth of 50 km in the area. The resistivity model shows that the low resistivity in the shallow part of the basin is related to the Cenozoic loose sedimentary cover, while the resistivity values of the mountains around the basin and the magmatic rock uplift zone are higher. The electrical model also shows that the high-conductivity layer is widely distributed in the middle and lower crust (15~35 km) of the basin, and direction of the high-conductivity layer is consistent with that of NW–SE fault in the basin. These high-conductivity layers may be the principal reason for the high heat flow values in the Gonghe Basin. Our resistivity model also shows that there is an obvious discontinuity between high- and low-resistivity blocks at different depths in the middle and upper crust. These discontinuities are consistent with the faults observed on the surface, which are related to the strong topographic relief. Our electrical model shows that these faults in the middle and upper crust are connected with the high-conductivity layer as the channel of heat transfer to the shallow part. Finally, the heat energy is enriched in the Triassic granite to form dry hot rock (HDR). The 3D-magnetotelluric imaging results depict the 3D-distribution characteristics of the geothermal system in the eastern and southern parts of the Gonghe Basin.
1 January 2023 in Earth Science-Journal of China University of Geosciences
Based on the concept of an equivalent eddy current, anomaly field inversion provides an efficient and rapid inversion method for borehole transient electromagnetic (BHTEM) measurements. It enables the utilization of the equivalent eddy current to rapidly process and interpret BHTEM data. This method allows for the accurate determination of the central position and spatial distribution of anomalies. However, the equivalent eddy current method is solely applicable to the inversion of the anomaly field. Given that the measured data frequently contain strong background field information, it is challenging to directly apply the equivalent eddy current approach to the inversion and interpretation of the measured data. To address the aforementioned issues, in this study, we innovatively put forward a method. Specifically, we utilize the response of the layered earth to simulate the background field and subtract the background field from the measured data through the “difference method” to extract the anomaly field. Subsequently, by integrating the equivalent eddy current method, the inversion of the anomaly field was accomplished. Eventually, a rapid quantitative inversion and interpretation of BHTEM data were achieved. We applied this approach to extract the pure anomaly from the measured data of the zk506 borehole in the Baishiquan mining area, Xinjiang, and then conducted equivalent eddy current inversion. The spatial position and distribution characteristics of the concealed ore bodies near the zk506 borehole were successfully pinpointed. Validation by the zk507 and zk508 boreholes confirmed that the main anomaly of the nickel ore body is positioned in the southeast of the boreholes, dipping northwestward. This outcome validates the accuracy of the BHTEM inversion interpretation and rectifies the geological understanding obtained from the zk506 single borehole. It demonstrates the effectiveness and significance of the pure anomaly extraction based on the layered-earth model and equivalent eddy current inversion in the exploration of high-conductivity sulfide ores.
The strong multi-stage tectonic movement caused the northwest of the North China Plain to rise and the southeast to fall. The covering layer in the plain area was several kilometers thick. In addition to expensive drilling, it is difficult to obtain deep geological information through traditional geological exploration. In this study, gravity, magnetotelluric (MT) sounding and shallow seismic methods are used to explore the basement relief and stratigraphic structure of the alluvial proluvial area in front of Taihang Mount in the North China Plain so as to understand the geological structure and sedimentary evolution of the area. The gravity anomaly map reveals the basement uplift, depression shape and faults distribution on the horizontal plane in the whole area. The MT profile reflects the geoelectric characteristics of the three-layer distribution in the Cenozoic. The seismic profile deployed on the Daxing Uplift depicts the structural style of the uplift area. The well-to-seismic calibration establishes the relationship between the lithostratigraphic and the wave impedance interface so that we can accurately obtain the shape and depth of the bedrock surface and further subdivide Cenozoic strata. Finally, we have improved the accuracy of interface inversion by using a variable density model based on density logging parameter statistics to constrain the depth of geological interfaces determined through drilling and multi-geophysical methods. Through the combination of geology and comprehensive geophysics, we have obtained the undulating patterns of Paleogene and Quaternary bottom interfaces, the structural styles of the basement and the distribution of faults in the survey area, which provide strong support for the study of neotectonic movement and sedimentary environment evolution since the Cenozoic. The successful application of this pattern proves that geophysical surveys based on prior geological information are an important supplementary tool for geological research in thick coverage areas.