The dead-time effect seriously affects the soft-switching performance and operating efficiency of the dual-active-bridge converter, and also causes problems such as reduced duty cycle, distortion of voltage and current waveforms, and narrowed transmission power range. The proposal of the five-degree-of-freedom modulation strategy transforms the working voltage waveforms of the primary and secondary sides as well as the inductor current waveform of the DAB converter from symmetric to asymmetric, while the dead-time issue still persists. Based on the five-degree-of-freedom modulation strategy, this paper analyzes the electrical characteristics of the converter before and after the introduction of dead time, designs switch drive pulses to avoid the dead time, and proposes a dead-time compensation modulation strategy based on five-degree-of-freedom phase shift. The results show that the proposed dead-time compensation control strategy can avoid problems such as voltage and current waveform distortion and reduction in the soft-switching power range caused by dead time, realizing dead-time compensation in the full power range. Experimental measurements show that, for different voltage transmission ratios, the maximum efficiency improvement is approximately 3.8–4% and the current stress is reduced by 2.11% to 3.13% under low-power operating conditions. The maximum efficiency improvement is approximately about 1.4–2.8% and the current stress is reduced by 1.84% to 2.53% under high-power operating conditions.
The objective of this study was to enhance the tracking effectiveness of the position adjustment for the electronic throttle in electric vehicles, as well as boost fuel efficiency and the dynamic performance of the vehicles. Firstly, a mathematical model, which pertains to the electronic throttle system, is established, and subsequently, the nonlinear uncertain system is made into a linear uncertain system. Subsequently, a self-coupling PID control law is designed, and an analysis is conducted on the system’s stability and its capacity to reject disturbances. Secondly, taking into consideration that the parameters of the PID controller with self-coupling mechanism are related to the system’s response speed, disturbance rejection capability, and overshoot, a self-adjusting speed factor transition function is put forward to address the conflict between speed and overshoot. Finally, numerical simulations and experimental tests are carried out. The results verify that, compared with the conventional PID controller, ADRC (Active Disturbance Rejection Control), and fuzzy PID, the proposed controller has a faster response speed, higher control accuracy, and better robustness.
In this paper, an efficient magnetic coupler featuring tight coupling and precise alignment is proposed for unmanned aerial vehicle (UAV) wireless charging systems. The design integrates ArUco markers for accurate landing guidance, a position-limiting guide groove to facilitate mechanical alignment, and a dual-coil tightly coupled configuration to significantly enhance charging efficiency. Specifically, the dual-coil structure is carefully optimized to maximize magnetic coupling and energy transfer performance. Additionally, an improved electromagnetic shielding structure is implemented to reduce electromagnetic leakage and further improve system efficiency. A suitable wireless charging circuit topology is then designed and thoroughly analyzed to match the proposed magnetic coupler, enabling constant-voltage charging operation. The performance of the system is validated through both finite element simulations using ANSYS Maxwell and experimental testing on a prototype setup. Results demonstrate that the integration of ArUco-based visual guidance with the mechanical alignment mechanism achieves a landing deviation of ±12.5 mm without requiring auxiliary positioning components, thereby simplifying system architecture. Under the tightly coupled configuration, the proposed system delivers 78.8 W of charging power to a UAV with a peak efficiency of 95.93%, confirming its effectiveness and high performance.
The dual-active-bridge (DAB) converter is the core component of the DC micro-grid system; it has the advantages of topological structure symmetry, high efficiency, and high-power density. Model predictive control (MPC) is often employed to improve the dynamic response characteristics of the system, but its strong parameter dependence is a key factor limiting the development of MPC. Therefore, a model-free predictive control (MFPC) method combining an ultra-local model with model predictive control is proposed to solve the problem of strong dependence of traditional MPC on system model parameters. Firstly, establish the ultra-local mathematical model of the DAB converter. The system’s lumped disturbances are identified using the residual prediction method and substituted into the discrete model of the system at the next time step to achieve model-free prediction. Secondly, a minimum back-flow power constraint is added to the cost function to improve the steady-state performance of the converter. Thirdly, in the extended phase shift modulation, the Lagrange multiplier method (LMM) is proposed to reduce the current stress, ultimately achieving the collaborative optimization of the comprehensive performance of the DAB. Finally, a simulation model is built using MATLAB/Simulink, and compared with traditional control methods, the voltage ripple has been reduced by 51.3%, 89.1%, and 85.1%, respectively; the current stress significantly decreases both when the output voltage reference value changes and when the load resistance changes abruptly, and both can basically achieve zero back-flow power operation. The validity and superiority of the proposed strategy have been verified.
This paper presents an enhanced bipolar control strategy for 400 Hz three-phase inverters in aviation ground power supplies, with a focus on maintaining symmetry in power output under unbalanced load conditions. The strategy integrates Linear Active Disturbance Rejection Control (LADRC) for robust positive sequence voltage regulation, Proportional Integral with repetitive control (PI + RC) for harmonic suppression in positive sequence currents, and a Quasi-Proportional Resonance (QPR) controller for negative sequence components in the static coordinate system. By doing so, it simplifies negative sequence control and combines PI + RC to improve the dynamic response and eliminate periodic errors. In the context of symmetry, the proposed strategy effectively reduces the total harmonic distortion (THD) and the three-phase current imbalance degree. Simulation results show significant improvements: under balanced loads, THD is reduced by 41.5% (from 1.95% to 1.14%) compared to traditional PI control; under single-phase and three-phase unbalanced loads, THD decreases by 52.7% (2.56% to 1.21%) and 48.1% (2.39% to 1.24%), respectively. The system’s settling time during load transients is shortened by over 30%, and the three-phase current imbalance degree is reduced by 60–70%, which validates the strategy’s effectiveness in enhancing power quality and system stability, thus restoring and maintaining the symmetry of the power output.
To reduce the impact of periodic pulsating torque and non-periodic disturbances on the speed control performance of permanent magnet synchronous motors (PMSMs), a sliding mode variable structure control method incorporating iterative learning compensation and load torque observation compensation is proposed. First, iterative learning control (ILC) is designed to address periodic disturbances and suppress periodic torque ripple. A load torque observation compensator is developed to counteract non-periodic disturbances, thereby enhancing the system’s robustness against uncertain disturbances. Second, numerical simulations compare the proposed method with sliding mode control (SMC), sliding mode control with load torque observation compensation (SMC + LO), and linear active disturbance rejection control (LADRC). The simulation results demonstrate that the proposed control strategy achieves reduced torque ripple, improved system tracking, and strong robustness. Finally, physical experiments are conducted, and the results closely align with the simulations. Both simulation and experimental outcomes confirm the effectiveness of the proposed control strategy in enhancing the speed performance of permanent magnet synchronous motors.