The EHA (electro hydraulic actuator) has a notable advantage over conventional hydraulic actuators as it uses a closed-loop circuit, reducing the size and volume of oil, and eliminates pressure losses caused by valve orifices. However, accurate control performance of EHA is difficult to achieve using a traditional PID (proportional integral derivative) controller due to the strongly nonlinear, time-varying, and unknown dynamics of the system. Hence this paper seeks to address this problem by proposing a design of an intelligent controller for the EHA. The proposed adaptive fuzzy sliding mode controller (AFSMC) is developed as a hybrid of the adaptive, fuzzy logic, and sliding mode algorithms. To reduce costs and time, a virtual prototype approach is also proposed instead of experimentations to evaluate the performance of the proposed controller. The virtual model of the EHA is built in Amesime software, and then embedded into Matlab/Simulink where the AFSMC is developed and tested to obtain the position responses of the EHA. The results show that the AFSMC is highly successful and more efficient than the traditional PID at controlling the position of the piston accurately.
This paper will develop the restoring model of a commercial pneumatic artificial muscle (PAM) based on a McKibben structure, which comprises an elastic element connected with a viscoelastic element in parallel. The elastic element is generated by compressed air inside the rubber bellow; meanwhile, the viscoelasticity is affected by the rubber material. In particular, the viscoelastic property of the rubber material is proposed based on the Maxwell model. Instead of derivative of integer orders, an equation of motion of the fractional model is introduced to better capture the amplitude- and frequency-dependent property of the viscoelasticity of the PAM. The equation expressing the hysteresis loop due to the viscoelasticity of the PAM material will then be analyzed and built. A water cycle algorithm is employed to determine the optimal set of the proposed model. To evaluate the effectiveness of the proposed model, a comparison between the simulation calculated from the proposed model and experimental data is considered under harmonic force excitation. This study’s results give potential insight into the field of system dynamic analysis with the elastic element being PAM.
Not only has the dynamic stiffness of a rubber air spring been inherited by effects of the compressed air, but it has also been affected by hysteresis behaviors caused by the friction, viscoelasticity of bellow material. Hence, this paper will analyze comprehensively the stiffness model of a commercial rubber air spring. One of the first works is to predict the structure parameters including effective area, volume and their change rate. Then, the restoring force generated by compressed air will be analyzed and built through the theory of thermodynamics. The hysteresis model of the rubber bellow will be obtained based on the Berg’s frictional model connecting in parallel with fractional Kelvin-Voigt model. Next, an experimental apparatus is set up to identify the parameters of this model as well as evaluate the proposed restoring force model of the rubber air spring. The study results show that the analysis model of the rubber air spring matches well the measured data. This work will offer a helpful insight in the design of the vibration isolation system using rubber air springs as elastic elements.
The purpose of this work paper is to analyze the effects of friction on the hysteresis dynamic behavior of pneumatic artificial muscle (PAM). Due to the structure of the PAM, the dynamic response is not only affected by the compressed air but also the friction phenomenon. Indeed, the pipe of the PAM called the bellow is made from rubber simultaneously reinforced by metal fibers that are wrapped around the bellow. Hence, the effect of the friction between fibers, between fiber and rubber will be considered in the nonlinear dynamic of the PAM. From dynamic analysis, the complex stiffness model will be attained and analyzed. Comparison between the analysis model and experimental results is realized subjected to harmonic displacement excitation. The results proved the effectiveness of the analysis model. The studied model is a suitable tool in the field of systems vibration analysis using PAM as an elastic element, actuator.
As is well known, vibration, especially ultra-low-frequency vibration, is harmful to machinery’s accuracy and service life and even human health. This paper experimentally validates vibration isolation technology for low-frequency applications based on quasi-zero stiffness (QZS) properties. Firstly, a platform for isolating low-frequency vibration, referred to as LFVIP, is introduced, featuring a quasi-zero stiffness characteristic. Then, the dynamic stiffness of this platform is analyzed and established. Based on this analytical model, a solution for designing the platform to obtain the desired stiffness in the equilibrium state is suggested. Secondly, an experimental setup is established to verify the isolation performance of the platform under base displacement excitation. In addition, the isolation effectiveness of the LFVIP is compared with that of its linear counterpart (LC). The experimental results indicate that the LFVIP provides the starting isolation for effective isolation at approximately 2 Hz, while that of LC is around 6 Hz. Moreover, the vibration attenuation of the LFVIP is greater than that of the LC. Vibration isolation technology based on quasi-zero stiffness is superior to the LC, particularly in the low-frequency region. This work offers useful insights for the design of vibration isolators, suspension systems, and related applications, particularly by demonstrating how the superior vibration attenuation of the LFVIP can be leveraged to improve the performance of these systems.
15 March 2024 in Journal of Science and Technology - IUH
Khó khăn của người tàn tật hoặc người cao tuổi trong trong quá trình sử dụng xe lăn là di chuyển lên xuống cầu thang bộ. Vì vậy, việc chế tạo thiết bị hỗ trợ xe lăn di chuyển trên cầu thang là một lĩnh vực cấp thiết. Vì lý do đó, bài báo này trình bày tính toán thiết kế cơ cấu truyền động của thiết bị hỗ trợ xe lăn di chuyển trên cầu thang. Thiết bị hỗ trợ xe lăn lên xuống cầu thang có cơ cấu tách rời với xe lăn, nhỏ gọn, dễ tháo lắp, khi sử dụng chỉ cần một người trợ giúp.