Lithography simulation is a critical step in VLSI design and optimization for manufacturability. Existing solutions for highly accurate lithography simulation with rigorous models are computationally expensive and slow, even when equipped with various approximation techniques. Recently, machine learning has provided alternative solutions for lithography simulation tasks such as coarse-grained edge placement error regression and complete contour prediction. However, the impact of these learning-based methods has been limited due to restrictive usage scenarios or low simulation accuracy. To tackle these concerns, we introduce an dual-band optics-inspired neural network design that considers the optical physics underlying lithography. To the best of our knowledge, our approach yields the first published via/metal layer contour simulation at 1nm2/pixel resolution with any tile size. Compared to previous machine learning based solutions, we demonstrate that our framework can be trained much faster and offers a significant improvement on efficiency and image quality with 20× smaller model size. We also achieve 85× simulation speedup over traditional lithography simulator with ~ 1% accuracy loss.
Background: Although several techniques and implants have been developed to address bone loss in revision total knee arthroplasty (rTKA), management of these defects remains challenging. This review article discusses the indications and management options of bone loss following total knee arthroplasty based on preoperative workup and intraoperative findings.Main text: Various imaging modalities are available that can be augmented with intraoperative examination to provide a clear classification of a bony defect. For this reason, the Anderson Orthopaedic Research Institute (AORI) classification is frequently used to guide treatment. The AORI provides a reliable system by which surgeons can classify lesions based on their size and involvement of surrounding structures. AORI type I defects are managed with cement with or without screws as well as impaction bone grafting. For AORI type IIA lesions, wedge or block augmentation is available. For large defects encompassing AORI type IIB and type III defects, bulk allografts, cones, sleeves, and megaprostheses can be used in conjunction with intramedullary stems.Conclusions: Treatment of bone loss in rTKA continues to evolve as different techniques and approaches have been validated through short- and mid-term follow-up. Extensive preoperative planning with imaging, accurate intraoperative evaluation of the bone loss, and comprehensive understanding of all the implant options available for the bone loss are paramount to success.
The role of U-wire generated quadrupole-like magnetic field profile on loading of cold atoms in a magneto-optical trap (MOT) on atom-chip has been investigated. It is shown by simulations that the quadrupole field profile and the centre of the quadrupole field vary depending upon the U-wire current and bias field values. Moreover, the resemblance of generated field profile to the ideal quadrupole field critically depends on the values of current in U-wire and bias magnetic field. The observed number of trapped atoms in the MOT and its position has also been found to depend on the quadrupole field profile. The number of trapped atoms in the MOT reaches maximum when the field profile approaches close to an ideal quadrupole field. These studies are, in general, useful in optimizing the number in the MOT before transfer of these cold atoms to the microtraps of an atom-chip.
In this work, we report the development and characterization of an atom chip for magnetic trapping of cold atoms. For fabrication of the atom chip, a silicon substrate was used after depositing an insulating layer of silica ( ) on it. An adhesive chromium layer was further deposited on this substrate before the deposition of the final layer of gold. On this gold coated substrate, a z-shaped gold wire (cross section, ) was fabricated by a photo-chemical machining method. The chip wire was tested for current–voltage characteristics for its reliable operation in magnetic trapping. The atoms from an U-magneto-optical trap, after optical pumping, were directly trapped in the magnetic trap of the atom chip.
Here, we report our studies on the continuous loading of a U-magneto-optical trap (U-MOT) on an atom-chip with a rubidium-(Rb)-vapor-generated background using a dispenser source in an ultra high vacuum environment. Using the U-MOT loading curves, the partial pressure due to the Rb vapor and the pressure due to the background gas have been estimated near the MOT cloud position. The estimated pressure due to the Rb vapor increased from ∼ Torr to Torr as the Rb-dispenser current was increased from 2.8 to 3.4 A. The increase in dispenser current also resulted in a decrease in loading time as well as the lifetime of the MOT cloud. This study will be useful for magnetic trapping experiments where accurate information of the pressure in a chamber is important for the lifetime of the magnetic trap.