Gordon Henry Waller

Dr. Gordon Henry Waller

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 January 2025 in Energies
Verified
Journal Article
Open access
PDF file
RCRachel Carter
Rachel Carter
GWGordon Henry Waller
Gordon Henry Waller
CJConnor Jacob
Connor Jacob
DHDillon Hayman
Dillon Hayman
PWPatrick West
Patrick West
CLCorey T Love
Corey T Love
Herein, we investigate the performance and safety of four of the early-stage, commercial Na-ion batteries available in 2024, representing the most popular cathode types across research and commercialization: polyanion (Na-VPF), layered metal oxide (Na-NMF), and a Prussian blue analog (Na-tmCN). The cells deliver a wide range of energy density with Na-tmCN delivering the least (23 Wh/kg) and Na-NMF delivering the most (127 Wh/kg). The Na-VPF cell was in between (47 Wg/kg). Capacity retention under specified cycling conditions and with periodic 0 V excursions was the most robust for the Na-tmCN cells in both cases. Accelerating rate calorimetry (ARC) and nail penetration testing finds that Na-NMF cells do undergo thermal runaway in response to abuse, while the Na-VPF and Na-tmCN exhibit only low self-heating rates (<1 °C/min). During these safety tests, all cells exhibited off-gassing, so we conducted in-line FTIR equipped with a heated gas cell to detect CO, CO2, CH4, toxic acid gases (HCN, HF, NH3), and typical electrolyte components (carbonate ester solvents). Gases similar to those detected during Li-ion failures were found in addition to HCN for the Na-tmCN cell. Our work compares different types of commercial Na-ion batteries for the first time, allowing for a more holistic comparison of the safety and performance tradeoffs for different Na-ion cathode types emerging in 2024.

12 December 2024 in Journal of Power Sources
Verified
Journal Article
Closed access
PWPatrick West
Patrick West
NLNicolas Leport
Nicolas Leport
DHDillon Hayman
Dillon Hayman
RCRachel Carter
Rachel Carter
CLCorey T. Love
Corey T. Love
GWGordon Henry Waller
Gordon Henry Waller

5 June 2026 in Journal of the Electrochemical Society
Verified
Journal Article
Closed access
LMLouis V. Morris
Louis V. Morris
JHJames L. Hart
James L. Hart
ZWZoey Warecki
Zoey Warecki
CLCorey T Love
Corey T Love
RCRachel Carter
Rachel Carter
GWGordon Henry Waller
Gordon Henry Waller
The adoption of sodium metal anodes is limited due to their poor coulombic efficiency stemming from dendritic plating morphologies and incomplete solid electrolyte interface (SEI) formation. This study presents a sodium metal battery electrolyte formulation utilizing lithium hexafluorophosphate as an additive, which selectively decomposes at the sodium metal interface to form a highly uniform, compact, and inorganic-rich SEI layer. This improved passivation layer enables >99% columbic efficiency operation of zero-excess sodium metal anodes. The mechanism of action of this additive is further elucidated using advanced surface characterization techniques including X-ray photoelectron spectroscopy (XPS) and scanning transmission electron microscopy (STEM) to show that SEI layers formed on zero-excess sodium metal anodes in the presence of LiPF 6 are thinner and more uniform than those formed in electrolytes without additives. Further, electron energy loss spectroscopy (EELS) reveals that SEI layers formed in the presence of LiPF 6 are enriched in lithium fluoride, a known component of high-quality SEI films in lithium-based battery systems and a direct decomposition product of the LiPF 6 additive, further establishing the role of LiPF 6 as a sacrificial film-forming additive for the stabilization of Na metal anode interfaces.

7 July 2026 in ECS Meeting Abstracts
Verified
Journal Article
Closed access
GWGordon Henry Waller
Gordon Henry Waller
CPCynthia Pyles
Cynthia Pyles
PWPatrick J. West
Patrick J. West
ADAdam Dunkelberger
Adam Dunkelberger
MSMichael W Swift
Michael W Swift
BFBoris N. Feygelson
Boris N. Feygelson
Low-temperature molten salt electrolytes for lithium batteries (e.g. (EMIM-TFSI/LiTFSI and the Li-K FSA eutectic mixtures [1, 2]) enable operation of electrochemical devices near ambient temperatures in an analogous fashion to conventional salt-in-solvent electrolytes. However, for certain applications involving long periods of inactive storage, the ability to freeze the electrolyte for low-self discharge storage is desirable. In this presentation, we will describe the electrochemical behavior as well as the thermal and structural stability of low-temperature molten salts at various temperatures throughout the melt-freeze cycle. At elevated temperatures, enhanced ionic conductivity and electrochemical kinetics are observed, then the cells can still be cooled to ambient conditions for storage, resulting in a dramatic drop in ionic conductivity which arrests self-discharge. We identify the changes in electrochemical behavior as measured by Electrochemical Impedance Spectroscopy (EIS), and structure as measured by ex situ X-ray Diffraction (XRD) and vibrational spectroscopies. Interestingly, the low temperature molten salts in this study show some hysteresis in structural and electrochemical properties when solidified, transitioning from a crystalline and relatively well-ordered structure as observed by XRD and vibrational spectroscopy. In the crystalline state the electrolytes have extremely low conductivity at room temperature, while as a molten liquid they exhibit conductivity comparable to conventional salt-in-solvent electrolytes. Cooling the molten liquids results in an amorphous and viscous phase of intermediate conductivity. Spectral shifts of the Raman-active S-N-S bend characteristic of FSA and TFSI allude to differences in coordination structure as a function of temperature. Fourier transform infrared (FTIR) studies and molecular dynamics simulations corroborate Raman by identifying structural changes and the potential presence of degradation products. These intriguing properties motivate our work characterizing EMIM-TFSI/LiTFSI and the Li-K FSA eutectic before and after melting and freezing cycles. Additionally, time-resolved techniques such as two-dimensional infrared (2DIR) spectroscopy relate ultrafast dynamics of the anions to bulk properties of molten salts. Finally, we further extend our work by describing these electrolytes in prototypical electrochemical systems, notably a Li-metal anode vs. FeS2 cathode full-cell. Physical Chemistry Chemical Physics, 2014. 16(24): p. 12341-12349. Matter, 2023. 6(12): p. 4357-4375.

23 December 2024 in Preprints.org
Verified
Preprint
Open access
PDF file
RCRachel Carter
Rachel Carter
GWGordon Henry Waller
Gordon Henry Waller
CJConnor Jacob
Connor Jacob
DHDillon Hayman
Dillon Hayman
PWPatrick West
Patrick West
CLCorey T Love
Corey T Love
Herein we investigate the performance and safety of four of the early-stage, commercial Na-ion batteries available in 2024, representing the most popular cathode types across research and commercialization: polyanion (Na-VPF), layered metal oxide (Na-NMF), and Prussian blue analog (Na-tmCN). The cells deliver a wide range of energy density with the Na-tmCN delivering the least (23 Wh/kg) and Na-NMF delivering the most (127 Wh/kg). Capacity retention under specified cycling conditions and with periodic 0V excursions was the most robust for the Na-tmCN cells in both cases. Accelerating rate calorimetry (ARC) and nail penetration testing finds that Na-NMF cells do undergo thermal runaway in response to abuse, while the Na-VPF and Na-tmCN exhibit only low self-heating rates (<1 °C/min). During these safety tests, all cells exhibited off-gassing, so we conducted in-line FTIR equipped with a heated gas cell to detect CO, CO2, CH4, toxic acid gases (HCN, HF, NH3), and typical electrolyte components (carbonate ester solvents). Gases similar to those detected during Li-ion failures were found in addition to HCN for the Na-tmCN cell. Our work compares different types of commercial Na-ion batteries for the first time allowing for a more wholistic comparison of the safety and performance tradeoffs for different Na-ion cathode types emerging in 2024.

24 November 2025 in ECS Meeting Abstracts
Verified
Journal Article
Closed access
RCRachel Carter
Rachel Carter
TKTodd Kingston
Todd Kingston
PWPatrick J. West
Patrick J. West
JKJacob Knuerr
Jacob Knuerr
JPJun-Sang Park
Jun-Sang Park
CLCorey T. Love
Corey T. Love
Thermal variations can evolve within Li-ion batteries as a result of (1) applied cooling, (2) varied thermal conductivity of components, or (3) local defects. We investigated the role of through-plane (current collector to current collector) thermal gradients on li-ion coin cells and single layer pouch cells and observed rapid degradation (within 10 cycles) with a thermal gradient of ~2⁰C. Data analysis and post mortem of the electrode determined that directionality of the through-plane gradient dictated positive electrode or negative electrode dominated degradation modes. We note that within a commercial cell, if a thermal gradient evolves through the layers, alternating thermal gradients will develop due to the use of double-sided electrode coatings on each current collector. We probe the response of 18650 cells undergoing cycling through operando diffraction experiments at the Advanced Photon Source. Extensive cycling of commercial cells under similar cooling environments reveals more rapid degradation than cells subject to less cooling. Further, in efforts to understand the fundamental thermodynamic pheonomena contributing to accelerated degradation, we isolated the response of the electrode and electrolyte components to a thermal gradient using novel electrode entropic potential and solvent entropy measurements. The talk concludes with recommendations to limit thermal gradients and limit performance degradation.