This paper presents a proposal for slabs reinforced with 3D steel reinforcements. Two configurations of 3D steel reinforcement, manually fabricated using 4 mm diameter rods, were investigated: cubic and square pyramid truss lattices. Two control groups were produced: a non-reinforced slab and a linear steel rod-reinforced slab. Three-point bending tests were conducted to assess the flexural behavior of the slabs. The results were analyzed in terms of flexural strength, peak load, mid-span displacement, energy absorption, crack formation, and ductility. The digital image correlation (DIC) technique was employed to capture the full-field principal strain and determine the mid-span displacement at the point of crack initiation. Furthermore, the compression capacity of each slab was evaluated. The results were compared with those of the non-reinforced and linear reinforced slabs, revealing that the slab with the cubic truss lattice configuration exhibited the highest bending moment capacity. While the square pyramid truss slab demonstrated relatively low bending strength, it exhibited exceptional energy absorption characteristics. In terms of ductility, the cubic truss-reinforced slab showed superior performance. When compared to the slabs with linear rod reinforcement, the 3D-reinforced slabs with cubic and square pyramid configurations enhanced the bending strength by approximately 51.19% and 47.32%, respectively. Overall, this study shows that the oblique connectors in the pyramidal reinforcement, compared to the vertical connectors in the cubic reinforcement, provide greater ductility and promote a more uniform distribution of smaller cracks, thereby enhancing energy absorption.
12 April 2024 in Pädi Boletín Científico de Ciencias Básicas e Ingenierías del ICBI
En este trabajo se evalúa la deflexión de dos propuestas de losa aligerada con peralte de 50 mm y estructura tridimensional embebida. Se proponen dos configuraciones de estructura (piramidal y cúbica) de varilla de acero grado 6000 de 4mm de diámetro. En una primera etapa, se evalúa la deflexión en losas convencionales mediante un método analítico y, posteriormente, se determina la deflexión en este tipo de losas mediante el método de elementos finitos, usando el software ANSYS. A partir de la validación de las simulaciones con el software, se procedió a realizar las mismas simulaciones ahora en las losas con estructura tridimensional. Los resultados obtenidos indican que las estructuras tridimensionales proveen más resistencia ante la deflexión en comparación con un armado de acero convencional. Además, se encontró que la estructura cúbica es la más resistente ante la flexión. Se discute la posible aplicación de losas con armado tridimensional para optimización de materiales mediante disminución del peralte en vivienda.
El objetivo del presente trabajo es realizar un análisis comparativo de investigaciones relacionadas a la determinación de propiedades físico-mecánicas de unidades de construcción (adobes y ladrillos) hechos de suelo, suelo-cemento y concreto con refuerzos diversos para proveer un panorama sobre procedimientos que conduzcan a la mejora del desempeño de estas unidades de construcción. Se analiza la variación porcentual de resistencia a la compresión, tensión, flexión, aislamiento térmico, densidad y absorción de agua acorde al tipo de refuerzo y mortero base. La incorporación de cemento como refuerzo parece tener el mayor efecto en la mejora de desempeño por resistencia a la compresión, los plásticos al aislamiento térmico, densidad y absorción de agua y los vegetales en resistencia a la tensión.
The ultrasonic pulse velocity (UPV) method is widely used for determining the dynamic modulus of elasticity of concrete. Traditionally, this approach requires assuming Poisson’s ratio (arbitrary values ranging from 0.1 to 0.25), regardless of the actual properties of the tested material. Such assumptions can lead to inaccurate estimations of the elastic modulus and limit the reliability of the method. In this study, an experimental methodology is proposed to enhance the accuracy of the estimation of the elastic modulus of concrete by combining digital image correlation (DIC) with UPV testing. The DIC technique is used during axial compression tests to directly measure the Poisson ratio of cubic concrete samples, while the dynamic modulus of elasticity is determined through UPV measurements. Subsequently, conversion models from the literature were applied to estimate the static modulus of elasticity from the dynamic modulus. The obtained values are compared with the experimental measurements of the static modulus, showing strong consistency and validating the proposed approach. The results highlight two key findings: (i) incorporating the actual Poisson ratio of the material significantly improves the precision of modulus predictions obtained via UPV, and (ii) DIC provides a reliable and adaptable tool for measuring Poisson’s ratio in concrete. Overall, the integration of DIC and UPV offers a robust and non-destructive framework for improving the assessment of mechanical properties of concrete.
16 February 2026 in International Journal of Combinatorial Optimization Problems and Informatics
This paper presents an innovative method for qualitative reasoning in the conceptual synthesis of mechanisms, leveraging AI-derived knowledge-based principles. The methodology allows for discretizing a mechanism's overall behavior without computational implementation. Relative motion between components, represented as qualitative states, is captured in a qualitative motion vector. These vectors form a general movement matrix that characterizes the mechanism's behavior, providing insights into component functions, movements, and transitions. By using ratchets as restriction functions, underlying behaviors are isolated from the matrix. These behaviors are used to generate conceptual designs for new mechanisms fulfilling specific kinematic functions. A case study is presented: synthesizing a mechanism that converts oscillatory rotation into unidirectional rotation using a differential gear train. The qualitative behavior of the resulting design is visualized in a vector diagram and compared with a CAD simulation. This method provides a knowledge base for training AI models in conceptual synthesis without needing specialized software. Smart citations: https://scite.ai/reports/10.61467/2007.1558.2026.v17i2.1208Dimensions.Open Alex.
6 April 2026 in Pädi Boletín Científico de Ciencias Básicas e Ingenierías del ICBI