The past several years have witnessed the rapid development in effectively transforming randomly distributed water kinetic energy into electrical energy, especially triggered by the emergence of droplet‐based electricity generators (DEG). Despite this, it still suffers from relatively low average power density, which is also achieved at the cost of long charging time, the time to reach stable and saturated surface charge density either through continuous droplet impingement or precharging. Although the harvested energy per droplet in DEG remains as the dominant metric, ultrahigh instantaneous output and short charging time are equally important in some specialized applications such as instantaneous luminescence. Here, we conduct systematical modeling and optimization to build the link between the hydrodynamic and electrical systems, which enables us to determine ultrahigh instantaneous output and short charging time by tailoring parameters such as dielectric layer thickness, droplet ion concentration, and external load. We envision that this strategy in achieving ultrahigh instantaneous output as well as shortening charging time would provide insights and design routes for water energy harvesting.
The utilization of water energy through the Single Electrode Droplet-Based Electricity Generator (SE-DEG) represents a universal and high-efficiency method for water energy harvesting. Previous research has extensively elucidated the working principle of SE-DEG based on bulk effect. However, scant attention has been paid to the investigation of the electrical characteristics surrounding the SE-DEG. Remarkably, the electrical characteristics around the SE-DEG can be exploited to generate electricity and harvest corresponding energy. Here we evaluate the electrical characteristics around the SE-DEG by arranging extra electrodes. An interesting phenomenon is found that, on the premise of no contact between extra electrodes and the droplet, there is opposite electricity output from extra electrodes synchronously when the droplet contacts on the PTFE film and SE-DEG electrode and outputs the electricity. This phenomenon is comprehensively explained and verified from working mechanism, the impacts of different arrangements and the array design of extra electrodes. Significantly, utilizing the electrical characteristics could harvest additional kinetic energy with extra electrodes in SE-DEG. This investigation is expected to provide new insights into the future harnessing of water kinetic energy within the SE-DEG framework.
This work presents the first demonstration of the transistor-free memory-diode (MD) array fabricated on Ge-on-Insulator (GeOI), which can work as an ultra-compact 8 F 2 ternary content addressable memory (TCAM). Through the wafer bonding and thinning techniques, the Ge layer in the GeOI structure maintains the monocrystalline quality originated from bulk Ge to ensure the Fermi-level pinning effect, forming an effective Schottky barrier with low reverse-bias leakage currents. Furthermore, an ultra-thin Y-doped GeO x layer is introduced to suppress the surface-state current, enabling a higher rectifying ratio. Thanks to the ultra-high rectifying (> 2 × 10 5 ) and sufficient on/off ratios (> 500), the 4-bits MD-TCAM array shows over 2 orders differences between the match and mismatch currents, which experimentally verifies the feasibility and accuracy of parallel data search.
This paper presents the concept to optimize the performance of a piezoelectric MEMS speaker with a cantilever diaphragm array by delicate structure design. The optimization focuses on the dimensions design of each cantilever unit of the array to balance the sound pressure level and frequency range under the condition of a limited area. The optimized design was first proposed based on the simulation and followingly a proof of experiment is conducted by fabricating a piezoelectric cantilever diaphragm array on a SOI wafer. As a result, measurements in the free field illustrate that the maximum SPL of the proposed microspeaker reaches 99 dB in the range of 200 Hz – 20 kHz with 3.0 V p-p driving voltage.
Ultra-low-resolution (ULR) thermal array sensors (e.g., ) offer a privacy-preserving and cost-effective paradigm for intelligent edge perception. However, extracting robust spatial features is severely hindered by extreme spatial aliasing, background thermal interference, and environmental temperature drift. In this paper, we propose VMEMSTNet, an ultra-lightweight framework that tackles the ULR perception bottleneck through a thermodynamics-inspired cross-modal learning strategy. Rather than treating ULR recognition purely as a computer vision task, our approach integrates the underlying sensing physics. To bridge the resolution gap, we leverage a high-resolution visual modality strictly as offline cross-modal guidance. Specifically, a YOLOv8n-seg teacher provides spatial shape priors via Gaussian thermal diffusion—explicitly mimicking physical heat dissipation for spatial knowledge translation—while a MobileNetV2 teacher guides semantic probability distillation. Furthermore, a thermodynamics-inspired preprocessing pipeline fuses dynamic quantile-based normalization with absolute temperature difference () to maintain contrast consistency across environmental drifts. Using hand gesture recognition as a representative spatial classification task, experimental results demonstrate that VMEMSTNet achieves 95.7% accuracy. Remarkably, it outperforms heavier generic edge models while utilizing only 20.0 k parameters and 0.135 MFLOPs. By effectively decoupling spatial semantics from thermodynamic noise, this work establishes a robust, hardware-aware deployment pathway for ULR thermal perception on resource-constrained microcontrollers.