Deok Ha Kim

Mr. Deok Ha Kim

Mechanical Engineering, Hanyang University, Seoul, Republic of Korea
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 January 2024 in IEEE Access
Verified
Journal Article
Open access
DKDeok Ha Kim
Deok Ha Kim
Jong-Hyeon ParkJong-Hyeon Park
Jong-Hyeon Park
Controlling quadruped robots during dynamic motions presents significant challenges due to constraints on ground reaction forces and the inherent complexity of their dynamics. Model predictive control (MPC) has shown promise in addressing these challenges. However, the performance of MPC strongly relies on the accuracy and complexity of the model, making the modeling process critical for dynamic locomotion control. This paper introduces a novel approach using the reduced single rigid body model (SRBM) and an associated MPC for achieving high-frequency control—crucial for highly dynamic locomotion. The reduced SRBM is derived by isolating the key components responsible for robot balance from the full SRBM, reducing model complexity without compromising control performance. Additionally, the planar kinematics is developed that considers the motions neglected in the reduced model. This enables the design of foot trajectories that facilitate omni-directional motion and yaw control. To validate the proposed method, computer simulations are conducted under various scenarios. The simulations demonstrate that the quadruped robot can achieve galloping speeds of up to 7 m/s while remaining stable even when subjected to a lateral disturbance of 200 N.

19 October 2022 in IEEE Access
Verified
Journal Article
Open access
SHSung Wook Hwang
Sung Wook Hwang
DKDeok Ha Kim
Deok Ha Kim
JPJaehwan Park
Jaehwan Park
Jong-Hyeon ParkJong-Hyeon Park
Jong-Hyeon Park
Under-constrained cable-driven parallel robots (UCCDPRs) manipulate the end-effector (EE) by employing fewer number of cables than the degree of freedom of the EE, which causes unwanted swaying motions and oscillations. These unwanted vibrations can be suppressed by using the regenerated EE trajectory through the input-shaper. However, in the case of the UCCDPR systems, generating the feasible EE trajectory and deriving the natural frequency for designing the input-shaper is not straightforward since finding the stable equilibrium configuration is challenging. This paper proposes a novel methodology to find the stable equilibrium configuration of the general UCCDPRs in the assigned EE position. With the proposed method, the EE trajectory can be reproduced as a vibration suppression trajectory through an input shaper designed based on the analysis of the natural frequencies, as well as generating feasible EE trajectories based on the equilibrium configuration. Also, even if the orientation trajectory is not given and only the position trajectory is given, the cable length to follow the given position trajectory of the EE can be obtained based on the equilibrium configuration corresponding to the given position trajectory. Computer simulations and hardware experiments were conducted to verify the effectiveness and performance of the proposed method.

11 August 2025 in Applied Sciences
Verified
Journal Article
Open access
PDF file
DKDeok Ha Kim
Deok Ha Kim
JCJaeuk Cho
Jaeuk Cho
Jong-Hyeon ParkJong-Hyeon Park
Jong-Hyeon Park
Controlling legged robots to run at high speeds or to traverse complex terrains remains challenging due to the difficulty of handling the interaction between the robot and the ground. Impedance control and model predictive control are widely used to account for ground reaction forces (GRFs) during dynamic locomotion. This paper introduces a model predictive impedance control (MPIC) method that combines the advantages of both strategies and applies it to a quadruped robot. The proposed approach reformulates MPIC within the single rigid body model (SRBM) framework and derives linear inequality constraints for the equivalent wrench, allowing explicit consideration of GRF limits while retaining compliant behavior against ground impacts and external disturbances. Furthermore, a novel optimized gait pattern based on a simplified dynamic model is introduced to minimize the effect of GRFs on the robot. The resulting gait improves stability compared to conventional gait patterns while maintaining a similar level of energy efficiency. The proposed method is validated through various simulations under diverse conditions. The results demonstrate that it enables the quadruped robot to run at a speed of 12 m/s while maintaining stability against repeated lateral disturbances.