The article is an overview of various materials used in power hydraulics for basic hydraulic actuators components such as cylinders, cylinder caps, pistons, piston rods, glands, and sealing systems. The aim of this review is to systematize the state of the art in the field of materials and surface modification methods used in the production of actuators. The paper discusses the requirements for the elements of actuators and analyzes the existing literature in terms of appearing failures and damages. The most frequently applied materials used in power hydraulics are described, and various surface modifications of the discussed elements, which are aimed at improving the operating parameters of actuators, are presented. The most frequently used materials for actuators elements are iron alloys. However, due to rising ecological requirements, there is a tendency to looking for modern replacements to obtain the same or even better mechanical or tribological parameters. Sealing systems are manufactured mainly from thermoplastic or elastomeric polymers, which are characterized by low friction and ensure the best possible interaction of seals with the cooperating element. In the field of surface modification, among others, the issue of chromium plating of piston rods has been discussed, which, due, to the toxicity of hexavalent chromium, should be replaced by other methods of improving surface properties.
30 June 2020 in Eksploatacja i Niezawodność – Maintenance and Reliability
The article presents the numerical investigation of the overhead crane’s energy consumption. The analysis is based on the hybrid model of the crane consisting of numerical model of drive mechanisms as bridge, trolley, hoist and also experimentally measured power consumption of each control unit. The numerical model was verified experimentally on the real crane. The investigation focuses on analyzing the energy consumption of the overhead crane in relation both to the travelled distance and also for the lifting and lowering heights of a suspended payload. Particular attention was paid on the cases straightly related to the hoist, as a main factor of improvements in the energetic efficiency of the overhead crane. Energy consumption was investigated for a variety of magnitudes of transported mass
The article is an overview of various methods of braking and controlling the movement of the piston rod under various load conditions. The purpose of this review is to systematize the state of the art in terms of efficiency, energy consumption and limitations of each method. The article discusses systems with different types of hydraulic actuators, operating under passive, active and variable load during the duty cycle of the piston rod. The existing literature was analysed in terms of applicability, reduction of energy consumption of the systems and even the possibility of energy return. Attention was paid to the costs and the need for additional power sources, as well as the problems and limitations of the presented methods. Based on the simulation model, energy consumption tests were carried out in systems with an actuator loaded with a variable force. There is a comparison of all methods in terms of actuator type, load, energy consumption and the possibility of energy recovery.
The article presents the experimental investigation of low-lifting capacity hydraulic scissor lift energy consumption. The analysis is based on experimental tests of two individual drives of the scissor lift: the conventional one and the variable-speed electro-hydraulic one. The investigation focuses on the study of the total energy consumption for lifting and lowering the scissor lift with different masses of transported cargo and also power consumptions of each element supplying these systems. Particular attention was paid to the significant impact of power supply on each control component as the main factor of reduction in the energetic efficiency of the low-lifting capacity scissor lift. A comparison of both drives indicated that the mass of transported cargo has a significant influence on the choice of the drive used. Results of the research show that significant energetic savings are obtained, as the modernized propulsion system consumes 67% energy of the standard one. A decrease in the percentage of energy losses with the increase in the mass handled led to the conclusion that the enhancement of propulsion systems in scissor lifts should be especially considered in machines carrying big loads.
The paper describes a new approach to the issue of controlling an indirect elevator with a bidirectional variable-speed pump and a simple controller based on the position sensor. The aim of this paper is to present a method of controlling the speed of the elevator to ensure smooth movement and proper positioning of the car on the floor, regardless of its load and ropes rigidity. The main feature of the proposed solution is the use of a frequency inverter in vector mode to control the speed of the car in both directions. The control function is based on virtual cams comparing actual measurements from the car position sensor. The proposed control strategy has been experimentally verified on the existing indirect elevator drive, and the obtained results indicate a very high accuracy in maintaining and shaping the speed and positioning of the car. The conducted research confirms the possibility of using a new method of controlling hydraulic and indirect elevators. The benefits of this method include a less complex hydraulic system, the control of overloads in the car and vibrations in the rope system, and the possibility of energy recovery.