The sol-gel process is a technique used to synthesize materials from colloidal suspensions and, therefore, is suitable for preparing materials in the nanoscale. In this work hydroxyapatite was used due to its known properties in tissue engineering. Hydroxyapatite Ca-10(PO4)(6)(OH)(2) is a bioactive ceramic which is found in the mineral phase of bone tissue and is known for its great potential in tissue engineering applications. For this reason, this material can be applied as particle aggregates on ceramic slurry, coating or film on materials with a poorer biological response than hydroxyapatite. In this work, hydroxyapatite gel was obtained by the sol-gel process and applied as nanoparticle aggregation in the mixture of hydroxyapatite and tricalcium phosphate to form a ceramic slurry. This process is the polymer foam replication technique used to produce scaffolds, which are used in tissue engineering. For HA gel characterization it was used enviromental scanning electron microscopy (ESEM), transmission electron microscopy (TEM), electron energy loss spectroscopy (EELS), scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray fluorescence (XRF). The crystallite size was calculated from XRD data using the Scherrer equation. The nanoparticles size before firing was approximately 5nm. The crystallite size calculated after calcination was approximately 63 nm. The EELS results showed that calcium phosphate was obtained before firing. After HA gel calcination at 500 degrees C the XRD results showed hydroxyapatite with a small content of beta-TCP. The scaffolds obtained by polymer foam replication technique showed a morphology with adequate porosity for tissue engineering
Surface parameters, such as microhardness, roughness, and microstructure, are used for quality control of a machining process. Given the fact that it is usually necessary to move the piece from the job zone to the quality control center to verify these parameters, the use of a portable quality control system could reduce the checking time of the process. The aim of this paper is to obtain the correlation of the typical machining process effect in the material surface with the Barkhausen noise to promote the online monitoring of the milling process. The Barkhausen noise is normally used to verify some magnetic properties of the ferromagnetic material and can be obtained using a simple procedure. The cutting temperature, surface roughness, microstructure, and, consequently, the Barkhausen noise can be modified by means of the cutting parameters variation. All these values depend on the level of residual stresses in the material. This paper presents an alternative to monitoring the milling surfaces of steel AISI SAE 1020 using the magnetic Barkhausen noise analysis.
Particle size is one of the most important factors to the successful application of calcium phosphate bioceramics as it may have an important role on its final properties such as mechanical resistance and reactivity. Thus, a process which results on very small and homogeneous particles is required, since it avoids further contamination derived from long milling times. On this context, a process such as sol-gel synthesis may be feasible, due to its simplicity on handling and its well known characteristic of producing homogeneous nanoparticles. Moreover, precipitated HA also may lead to satisfactory results regarding particle size and phase purity. The aim of this article was to demonstrate a preliminary characterization study of powders obtained by both methods and to compare them to a commercial sample available in Brazil. Characterization was made by XRD, Scherrer’s equation, XRF, SEM-LV, SEM-FEG and SEM-EDS. It has been found out that all samples consist of pure nanostructured hydroxyapatite with crystallite size between 37nm and 62nm.
Scaffolds produced with ceramics are commonly used as bone substitute. In this work calcium phosphate materials were used to produce the scaffolds, because HA and TCP have many similarities with bone tissue. For crystalline phase analysis the scaffolds were calcined at 750 °C and sintered at 1330 °C. Electron microscopy images showed HA and TCP nanoparticles and the compounds were identified by Fourier transform infrared spectrometer. X-ray diffraction showed this material to be mostly crystalline. X-ray fluorescence identified chemical contaminants. X-ray micro computerized tomography produces tomographic images of the objects in 360°. In vitro testing was used to study cells behavior in contact with this material in a controlled environment
Production Planning and Control is directly involved with production activities in the polymer packaging industry, aiming to produce more with fewer resources. This reduces polymer scrap, generating positive results in economic and environmental terms. The importance of reducing polymer waste during the extrusion process and the use of theoretical models and simulation tools, along with recycling and reprocessing practices, emerges as an effective strategy to improve production and minimize environmental impacts. This study aims to evaluate the economic and environmental gains of adopting activities/tools used in production planning and control in the polymer packaging industry. The research method adopted was a case study conducted through semi-structured interviews. It was concluded that polymer scrap in the production system was reduced through actions taken by production planning and control, contributing to the micro-level circular economy, generating significant economic and environmental gains.