Food waste is categorized as organic solid waste, which has a negative impact on environmental sustainability. Food waste was simultaneously used for the feasible generation of mixed volatile fatty acids (VFAs) and bio-hydrogen by deploying dark fermentation. Original anaerobic digested sludge was prepared via the shock technique with 50 g/L glucose under thermophilic temperature (55 °C). The pretreated inoculum was found capable of converting 10 g VS/L food waste to hydrogen with a rather high yield of 135.2 ± 7 mL H2/VSadded. The effect of various concentrations of food waste, including 10.2, 16.3, 20.3, and 26.4 g VS/L, on mixed VFAs production was subsequently carried out in batch dark fermentation. The highest butyric acid concentration (5.26 ± 0.22 g/L) in soluble metabolites was obtained from batch dark fermentation with 26.4 g VS/L of food waste. The dominant Clostridium thermobutyricum, Clostridium sporogenes, and Octadecobacter sp. found in the batch of dark fermentation of food waste could confirm the effectiveness of the load shock pretreatment method for inoculum preparation. The continuous stirred tank reactor (CSTR) inoculated with mixed cultures, also prepared via the load shock pretreatment method and without the addition of external nutrients, was operated by feeding 26.4 g VS/L food waste at the kinetically designed HRT for 4 days, corresponding to an organic loading rate (OLR) of 7.6 g VS/L·d. Under steady state conditions, promising butyric acid (5.65 ± 0.51 g/L)-rich mixed VFAs were achieved along with the hydrogen yield of 104.9 ± 11.0 mL-H2/g VSadded, which is similar to the upper side of the previously reported yields (8.8 ± 0.6–103.6 ± 0.6 mL-H2/g VS).
3 September 2018 in Malaysian Journal of Fundamental and Applied Sciences
Lignocellulosic material consists of lignin, cellulose and hemicellulose. Converting lignocellulosic biomass such as cow manure (CM) into value-added products provides a potential alternative. Hydrolysis of cellulose and hemicellulose is a limiting step during Anaerobic Digestion (AD) of lignocellulosic biomass. Lignin in lignocellulosic biomass is the barrier for hydrolysis, thus limits the biogas production. In this study, the effect of A.Fumigatus SK1 and Trichoderma sp. on enzymatic pre-treatment of CM was investigated with respect to the biogas production. Three set of anaerobic digestion assays were carried out, with a working volume of 500 mL at 35 ± 2°C and 120 rpm. The first set of fermentation contained untreated CM. The second set of fermentation involved addition of A.Fumigatus SK1, and the last set contained Trichoderma sp. Several analysis were conducted to determine the biomethane potential (BMP), anaerobic biodegradability, reducing sugars concentration and lignin removal of CM before and after pre-treatment. Result showed that, among both evaluated pre-treatment methods, CM treated with Trichoderma sp. gave the highest methane potential with 0.023 LCH4-STP g VS-1 compared to CM treated with A.Fumigatus SK1(0.011 LCH4-STP g VS-1). A good correlation have been found in this study between lignin removal and reducing sugar produced where, the total lignin removal after treated with Trichoderma sp. was 60% followed by 43% after treated with A.Fumigatus SK1.The reducing sugar produced after pre-treated with Trichoderma sp. and A.Fumigatus SK1 was about 9.59 and 4.91 μmol glucose, respectively. These results collectively suggested that CM treated with Trichoderma sp. could be a better pre-treatment method for the higher methane production in anaerobic mono-digestion process.
EFB and EFB-based mushroom compost (SMC) from Volvariella volvacea cultivation is a promising energy feedstock because it has adequate nutrient quality. The biochemical methane potential (BMP) and calorific value (CV) of this biomass are investigated. Other analyses such as proximate, compositional, and final analysis; thermogravimetric analysis (TGA); and Fourier transform infrared spectroscopy (FTIR) are also performed. The biomass samples consist of two types of EFB, namely fibers (F) and pellets (P) and SMC from the subsequent cultivation of Volvariella volvacea, with samples FS and PS from the first cultivation and FS2 and PS2 from the second cultivation. P produces the highest biological efficiency (BE) of 28% compared to 9.83% for F. Subsequent cultivation with FS and PS then produces only 2.9 and 6.83% of BE. A higher amount of methane is measured in samples P and PS2, while better biodegradability is observed in PS2 and FS2, suggesting that subsequent cultivation is a good pretreatment of the substrate for anaerobic digestion (AD). CV is highest in F (20.57 MJ/kg), followed by P (19.06 MJ/kg), which is comparable to commercial wood pellet. Samples F, FS, and FS2 have higher ash content, which is due to higher mineral content. The cellulose composition is reduced to almost 50% during cultivation due to fungal metabolism, which is also evidenced by FTIR analysis. TGA analysis revealed that EFB-based SMC exhibits higher weight loss during combustion compared to EFB, which reduces its thermal properties. SMC of EFB is a high potential biomethane feedstock, but not recommended as a fuel pellet.
Treatment of ammonia- and nitrate-rich wastewater, such as that generated in the aquaculture industry, is important to prevent environmental pollution. The anaerobic ammonium oxidation (anammox) process has been reported as a great alternative in reducing ammoniacal nitrogen concentration in aquaculture wastewater treatment compared to conventional treatment systems. This paper will highlight the impact of the anammox process on aquaculture wastewater, particularly in the regulation of ammonia and nitrogen compounds. The state of the art for anammox treatment systems is discussed in comparison to other available treatment methods. While the anammox process is viable for the treatment of aquaculture wastewater, the efficiency of nitrogen removal could be further improved through the proper use of anammox bacteria, operating conditions, and microbial diversity. In conclusion, a new model of the anammox process is proposed in this review.
1 May 2021 in Journal of Pure and Applied Microbiology
Biological treatment for textile wastewater always has a limitation in term of time of reaction and uncertainty along the process. This study focused on the decolorization of synthetic azo dyes in batch reactors with controlled thermotolerant anaerobic conditions. Less-volatile digested sludge collected from a palm oil biogas reactor was used as the organic biodegradation agent for azo dyes. Digested sludge contains high amounts of microbes with uncertain species viable for decolorization purposes. Sodium acetate trihydrate (C2H9NaO5) was used as carbon source and mixed with a specific composition of minimum salt media (MSM) in batch reactors as an additional nutrient. Digested sludge both in mesophilic (35°C) and thermophilic (55°C) conditions were found to be capable of decolorizing 100, 200 and 300 ppm of three types of azo dyes: Reactive Green 19 (45.56%, 69.73%; 63%, 73.49%; 70.02%, 75.92%), Reactive Orange 16 (46.08%, 78.4%; 64.21%, 85.52%; 74.95%, 85.91%) and Reactive Red 120 (29.11%, 85.32%; 63.35%, 87.69%; 72.02%, 89.5%) respectively after 7 days incubation time. Statistical analysis also showed that the anaerobic thermophilic conditions had significantly accelerated the decolorization process. The anaerobic thermophilic environment will be a good factor to include in future textile wastewater treatment plants.
Recovering oil and water from palm oil mill effluent reduces environmental pollution and promotes sustainable practices. An effective method to achieve this is ultrafiltration (UF), which uses semi-permeable membranes to separate oil, solids, and other contaminants from wastewater under pressure. To assess the most effective recovery method, an experimental comparison was conducted between PVDF and α-Al2O3 UF membranes at constant permeate of 20–50 LMH for PVDF and 20–70 LMH for α-Al2O3 membranes. Both membranes achieved 99.8% chemical oxygen demand (COD) rejection, with oil concentration factor (Fo) of 186.8% and 253.0%, and water recovery (Rw) of 46.6% and 60.5%, respectively. The permeate water quality was superior to the Malaysian discharge standards, and the fat, oil, and grease (FOG) content was suitable for phase separation processes. The optimal permeate fluxes, with stable transmembrane pressures (TMP), were observed at 40 LMH (PVDF) and 60 LMH (α-Al2O3). Total resistance (Rt) values were 1.30 × 1012 m−1 (PVDF) and 1.59 × 1012 m−1 (α-Al2O3). The ratio of irreversible to total resistances (Rir/Rt) was 0.02 (PVDF) and 0.06 (α-Al2O3), indicating minimal irreversible fouling. Overall, the α-Al2O3 membrane demonstrated superior performance in oil and water recovery with more stable operation compared to the PVDF membrane. UF membrane technology emerges as an efficient technique for recovering oil and water compared to conventional methods.