Ugur Caligulu

Prof. Dr. Ugur Caligulu


Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2010 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
AMAhmet Meyveci
Ahmet Meyveci
IKİsMail Karacan
İsMail Karacan
UCUgur Caligulu
Ugur Caligulu
HDHülya Durmuş
Hülya Durmuş

9 March 2013 in Arabian Journal for Science and Engineering
Verified
Journal Article
Closed access
PDF file
SBSoner Buytoz
Soner Buytoz
AOAyhan Orhan
Ayhan Orhan
AGAli Kaya Gur
Ali Kaya Gur
UCUgur Caligulu
Ugur Caligulu

12 May 2007 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
MTMustafa Taskin
Mustafa Taskin
UCUgur Caligulu
Ugur Caligulu
AGAli Kaya Gur
Ali Kaya Gur

1 May 2014 in Materials Testing
Verified
Journal Article
Closed access
AGAli Kaya Gur
Ali Kaya Gur
COCetin Ozay
Cetin Ozay
AOAyhan Orhan
Ayhan Orhan
SBSoner Buytoz
Soner Buytoz
UCUgur Caligulu
Ugur Caligulu
NYNecmettin Yigitturk
Necmettin Yigitturk
In this study, the plasma arc welded cladding of FeCrC and B4C powder mixtures alloyed with 70 wt.- % Cr on the surface of AISI 316 stainless steel was investigated. Application of the Taguchi method revealed respective effects on the abrasive wear resistance of the cladding layer on the stainless steel. The abrasive wear behaviour of the AISI 316 stainless steel surfaces coated with Fe-Cr-C and with 10 wt.-%, 15 wt.-%, 20 wt.-%, and 25 wt.-% B4C was investigated by using four loads and four distances for the 220 mesh SiC abrasive. Results were analyzed by variance analysis using ANOVA, and effects of parameters on the wear rate were determined as percentage rate. Furthermore, the error ratio was statistically evaluated. The experimental results were analyzed by the respective analysis of means and variance which is discussed in detail.

1 November 2011 in Materials Testing
Verified
Journal Article
Closed access
MTMustafa Taskin
Mustafa Taskin
UCUgur Caligulu
Ugur Caligulu
MTMustafa Turkmen
Mustafa Turkmen
For this study, X-Ray radiographic tests of AISI 430 and 304 stainless steels with AISI 1010 low-carbon steels welded by CO2 Laser beam welding (LBW) have been performed. Laser beam welding experiments were carried out under argon and helium shielding gas, at 2000–2250 and 2500 W heat input and 100-200-300 cm/min welding speeds. After this process, the radiographic tests of the welded joints were performed by X-Ray diffraction. The result of the radiographic tests indicated that with increasing heat input the widths of the deep penetration increased in all specimens. On the contrary, by increasing the welding speeds the widths of the deep penetration decreased. The best properties of the AISI 430 and 304 stainless and AISI 1010 low-carbon steel welds were observed at the specimens welded at 2500 W heat input and 100 cm/min welding speed.

Verified
Journal Article
Open access
MTMustafa Taskin
Mustafa Taskin
UCUgur Caligulu
Ugur Caligulu
In this study, modelling of microhardness values by means of artificial neural networks of Al/SiCp metal matrix composite material couples with diffusion method and manufactured by powder metallurgy process, were obtained using a backpropagation neural network that uses gradient descent learning algorithm. After diffusion bonding and relevant test, to prepare the training and test (checking) set of the network, results were recorded in a file on a computer. Then, the neural network was trained using the prepared training set. At the end of the training process, the test data were used to check the system accuracy. As a result the neural network was found successful in the prediction of modelling of microhardness values of Al/SiCp metal matrix composite material couples processed with diffusion method and behavior.