1 May 2014 in Materials Testing
In this study, the plasma arc welded cladding of FeCrC and B4C powder mixtures alloyed with 70 wt.- % Cr on the surface of AISI 316 stainless steel was investigated. Application of the Taguchi method revealed respective effects on the abrasive wear resistance of the cladding layer on the stainless steel. The abrasive wear behaviour of the AISI 316 stainless steel surfaces coated with Fe-Cr-C and with 10 wt.-%, 15 wt.-%, 20 wt.-%, and 25 wt.-% B4C was investigated by using four loads and four distances for the 220 mesh SiC abrasive. Results were analyzed by variance analysis using ANOVA, and effects of parameters on the wear rate were determined as percentage rate. Furthermore, the error ratio was statistically evaluated. The experimental results were analyzed by the respective analysis of means and variance which is discussed in detail.
1 March 2016 in Materials Testing
The study examines how, using wire electrical discharge machining (WEDM), the microstructural, mechanical and conductivity characteristics of the titanium alloy Ti6Al4V are changed as a result of heat treatment and the effect they have on machinability.Scanning electron microscope (SEM), optical microscope and X-ray diffraction (XRD) examinations were performed to determine various characteristics and additionally related microhardness and conductivity measurements were conducted. L18 Taquchi test design was performed with three levels and six different parameters to determine the effect of such alterations on its machinability using WEDM and post-processing surface roughness (Ra) values were determined. Micro-changes were ensured successfully by using heat treatments. Results obtained with the optimization technique of artificial neural network (ANN) presented minimum surface roughness. Values obtained by using response surface method along with this equation were completely comparable with those achieved in the experiments. The best surface roughness value was obtained from sample D which had a tempered martensite structure.
1 December 2021 in Materials Testing
In this study, the surface of AA-2024 alloy substrate was coated with an Al-B4C reinforced composite using hot press sintering. Al and B4C powders were synthesized by mechanical alloying. To this end, four samples were prepared. As a reference sample, AA-2024 substrate was coated with pure Al powder under 110 MPa pressure. In the other samples, the AA-2024 substrate was coated with metal matrix composites (MMCs) contained in Al-5 wt.-% B4C at 90, 110 and 130 MPa. The microstructure of the transition zone formed between the AA-2024 substrate and the coating layer of the coated samples, the microstructure of the Al/B4C MMCs coating, the macro hardness, the linear reciprocating and forth wear resistance of the coating layer were investigated. In addition, an optical microscope (OM), scanning electro microscope (SEM) images and EDS analysis of the microstructure were used. It was observed that the B4C powders were homogeneously distributed in the Al matrix in the microstructure of the coating layer. It was also found that the gaps between the grains in the microstructure of the coating layer and their size decreased with an increase in pressing pressure. Accordingly, it was concluded that macro hardness increased and weight loss decreased.
29 June 2021 in Journal of Mechanical Science and Technology
19 May 2021 in Arabian Journal for Science and Engineering
17 August 2023 in El-Cezeri Fen ve Mühendislik Dergisi
In this study, the effect of die surface angled hydro-mechanical deep drawing method (HMDDM) on sheet metal cup wall thickness and punch force was investigated as experimental and numerical analysis. In the works, 0.9 mm thick DIN EN 10130-1999 sheet metal material was used. The effect of variables on the test results was investigated by using die surface/blank holder angle, punch nose radius, die shoulder radius, chamber pressure and blank holder force as experimental parameters. Numerical analysis experiments were carried out using ANSYS 15.0 package program. Besides, experiments were performed according to the Taguchi experiment plan and L18 orthogonal array. The obtained data were analysed statistically by ANOVA analysis of variance in MINITAB 17.0 package program, and the effect of each parameter on the results was determined as a percentage. As a result, it was determined that the thinning was approximately 15% at most and the thickening was 10%.