The temperature and strain rate significantly affect the ballistic performance of UHMWPE, but the deformation of UHMWPE under thermo-mechanical coupling has been rarely studied. To investigate the influences of the temperature and the strain rate on the mechanical properties of UHMWPE, a Split Hopkinson Pressure Bar (SHPB) apparatus was used to conduct uniaxial compression experiments on UHMWPE. The stress–strain curves of UHMWPE were obtained at temperatures of 20–100 °C and strain rates of 1300–4300 s⁻¹. Based on the experimental results, the UHMWPE belongs to viscoelastic–plastic material, and a hardening effect occurs once UHMWPE enters the plastic zone. By comparing the stress–strain curves at different temperatures and strain rates, it was found that UHMWPE exhibits strain rate strengthening and temperature softening effects. By modifying the Sherwood–Frost model, a constitutive model was established to describe the dynamic mechanical properties of UHMWPE at different temperatures. The results calculated using the constitutive model were in good agreement with the experimental data. This study provides a reference for the design of UHMWPE as a ballistic-resistant material.

This work developed a method for calculating the Jones-Wilkins-Lee (JWL) equation of state (EOS) for the detonation products of aluminized explosives based on hexanitrohexaazaisowurtzitane (CL-20). On the basis of previous studies, chemical reaction equations, Hess’ law and Avogadro’s law were all incorporated in this process because of the non-ideal detonations of aluminized explosives. The EOS parameters were determined for explosive formulations comprising pure CL-20 as well as aluminized versions and compared to literature reports. Calculated pressure-specific volume curves were in good agreement with prior studies. A 50 mm cylinder test using a CL-20/Al/wax composition with a 75/20/5 mass ratio was conducted and the calculated EOS parameters were used to simulate the expansion of the cylinder wall. The experimental and simulation plots were found to agree within 5%, which confirms the validity of this method with regard to engineering analyses.

The mechanical properties of polyethylene (PE) materials are greatly influenced by their molecular structures, environmental temperature, and strain rate. In this study, static and dynamic compression tests were performed on two semicrystalline PE materials—ultrahigh molecular weight polyethylene (UHMWPE) and high-density polyethylene (HDPE). The stress–strain curves of HDPE and UHMWPE under uniaxial compression at temperatures of −40–120 °C and strain rates of 0.001–5500 s⁻¹ were obtained. The research findings suggest that both the UHMWPE and HDPE showed significant strain rate-strengthening effect and temperature-softening effect. In particular, HDPE exhibited better compression resistance and high-temperature resistance. The relationships between the yield stress and temperature and between the yield stress and strain rate for both materials were fitted, and the Cowper–Symonds constitutive model was built while considering the temperature effect. The parameters of the constitutive model were obtained and input into LS-DYNA software to simulate the dynamic compression process of HDPE. The simulation result was consistent with the test result, validating the accuracy of the constitutive parameters.

A thermal environment has a complex influence on the dynamic characteristics of fiber-reinforced composite materials and structures. It is challenging to consider the effects of high temperature and external vibration energy simultaneously on their nonlinear vibration response. In this research, the material nonlinearities, due to both the excitation amplitudes and the high temperatures, are studied for the first time, and a new nonlinear vibration model of fiber-reinforced composite thin plates in a thermal environment is proposed by introducing the nonlinear thermal and amplitude fitting coefficients simultaneously. Then, based on the classical laminated plate theory, the complex modulus approach, and the power function and the Ritz methods, dynamic governing equations in high-temperature environments are derived to solve the nonlinear natural frequencies and vibration responses and damping parameters. Moreover, the three-dimensional fitting curves of the elastic moduli and loss factors, excitation amplitudes, and temperature values are obtained so that the key nonlinear fitting coefficients in the amplitude- and temperature-dependent model can be identified. To validate this model, the experimental tests on CF130 carbon/epoxy composite thin plates are undertaken. It is found that the 3rd and 5th natural frequencies, vibration responses, and damping results obtained from the nonlinear model are consistent with the experimental measurements, and the mechanism of nonlinear thermal vibration behaviour is revealed.

In this paper, the plastic flow and fracture behavior of 3D-printed Ti6Al4V (TC-4) alloy under different temperatures (289–1073 K) and strain rates (0.1–4100 s⁻¹) were studied by using the MTS comprehensive experimental machine (MTS) and split Hopkinson pressure bar (SHPB) equipment. The patterns of the influence of temperature and strain rate on the plastic flow behavior of 3D-printed materials in different printing directions were analyzed and compared with those of the traditional TC-4. Based on the experimental data, the modified Johnson–Cook (J-C) constitutive model of 3D-printed TC-4 alloy was established, and the plastic deformation behavior of the material driven by detonation was studied by X-ray photography. The research results showed that under static loading conditions, the strength of the material (AM-P-TC-4) along the printing direction was much higher than the strength of the material perpendicular to the printing direction (AM-T-TC-4). However, there was no difference in material strength for different directions under dynamic loading. Second, under the same deformation conditions, the strength of the 3D-printed TC-4 alloy was considerably higher than that of the traditional TC-4 alloy, but adiabatic shear fracture could be more easily induced under dynamic compressive deformation conditions for the 3D-printed TC-4 alloy, and its fracture strain was substantially less than that of TC-4 alloys. The modified J-C constitutive model established in this paper could better describe the plastic flow behavior of the AM-P-TC-4 alloy under high temperature and high-strain rate deformation conditions.