Textured surfaces have been remarkable in improving the frictional performance of sliding contacts, particularly at instances such as boundary or mixed lubrication regimes. This article reports the results of an experimental and numerical study carried out by introducing surface textures in the form of protrusions to investigate its effects on friction performance under a mixed lubrication regime. The surface textures produced by the chemical etching process are tested on the pin on disc test rig by varying area density and height of the texture. In numerical simulation, the modified Reynolds equation (Patir–Cheng flow model) and asperity contact model (Greenwood–Tripp model) are solved for hydrodynamic and asperity pressures, respectively. The results indicate that the experimental measurements are qualitatively in good agreement with numerical predictions. Furthermore, the simulations are performed for different texture shapes by varying texture area density, height, and sliding velocity. The results depict that a maximum friction reduction of 87% with elliptical textures compared to the un-textured case.
Purpose: In an internal combustion engine, piston ring-cylinder liner tribo pair is one among the most critical rubbing pairs. Most of the energy produced by an internal combustion engine is dissipated as frictional losses of which major portion is contributed by the piston ring-cylinder liner tribo pair. Hence, proper design of tribological parameters of piston ring-cylinder liner pair is essential and can effectively reduce the friction and wear, thereby improving the tribological performance of the engine. This paper aims to use surface texturing, an effective and feasible method, to improve the tribological performance of piston ring-cylinder liner tribo pair. Design/methodology/approach: In this paper, influence of positive texturing (protruding) on friction reduction and wear resistance of piston ring surfaces was studied. The square-shaped positive textures were fabricated on piston ring surface by chemical etching method, and the experiments were conducted with textured piston ring surfaces against un-textured cylinder liner surface on pin-on-disc apparatus by continuous supply of lubricant at the inlet of contact zone. The parameters varied in this study are area density and normal load at a constant sliding speed. A comparison was made between the tribological properties of textured and un-textured piston ring surfaces. Findings: From the experimental results, the tribological performance of the textured piston ring-cylinder liner tribo pair was significantly improved over a un-textured tribo pair. A maximum friction reduction of 67.6 per cent and wear resistance of 81.6 per cent were observed with textured ring surfaces as compared to un-textured ring surfaces. Originality/value: This experimental study is helpful for better understanding of the potency of positive texturing on friction reduction and wear resistance of piston ring-cylinder liner tribo pair under lubricated sliding conditions.
11 May 2024 in Journal of Engineering and Applied Science
The present research is aimed to understand the influence of graphene-reinforced carbon/Kevlar hybrid fabric epoxy composites. Samples HG0, HG2, HG4, and HG6 are fabricated using four layers of fabric mat and with varying graphene weight percentage as 0, 2, 4, and 6 wt.%, respectively. Mechanical characterizations such as hardness, tensile, and flexural strength were individually assessed. Thermal stability is evaluated through thermos-gravimetric analysis. Composite HG6 with high filler loading showed 71% and 114.4% greater tensile and flexural strength compared to unfilled HG0 specimen. Similarly, HG6 exhibited greater thermal stability. Inclusion of graphene particles in higher concentration improved the interfacial bonding between fibre/matrix/filler system. Fracture surfaces are analysed using scanning electron microscopy to understand the failure mechanisms.
3 January 2023 in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
A five-layered aluminum–copper metal functionally graded material was developed through powder metallurgy process. The sample comprises different weight percentages of copper and aluminum that vary from 0 wt% to 100 wt % along the thickness direction. Erosion wear was performed on air jet erosion testing apparatus at a constant impact angle of 90 o and impact velocity of 151 m/s. It was observed that erosion wear decreases when there is an increase in copper content. Layer 1 comprising 100 wt% of copper has shown 76.92% lower wear compared to layer 5 (100 wt% of aluminum). Besides, erosion resistance was enhanced at graded layers due to the formation of Al 2 Cu phase during sintering. Abrasive wear of metal functionally graded material was evaluated on the pin-on-disc test apparatus. Experiments were conducted at different loading conditions on various abrasive surfaces (P120, P800, and P2000). Irrespective of abrasive surface, the specific wear rate of aluminum–copper metal functionally graded material sample increased with an increase in load from 5N to 15N. At 5N, abrasive wear of metal functionally graded material on P2000 grit surface was 87.7% and 27.19% lower compared to P120 and P800, respectively. Eroded and worn-out surfaces were examined microscopically to understand the wear mechanisms and are discussed in detail.