In the present study, we developed a new adsorbent product with zeolite crosslinked chitosan (ZL–CH hydrogel) to remove acid red 88 (AR88) in an aqueous solution. The effects of several factors, such as the comparison of ZL–CH hydrogel and the absence of chitosan, pH, adsorbent dosage, initial AR88 concentration, contact time, and ion strength, were determined. Obtained results showed that ZL–CH hydrogel improved AR88 removal compared to the absence of chitosan, with an adsorption capacity of 332.48 mg/g in equilibrium time of 1 min, and adding ionic strength had no significant effect. However, with optimal conditions at pH 2.0, dry ZL–CH became hydrogel due to protonation of amino and hydroxyl groups through hydrogen bonds in the AR88 solution. Volume fraction and interaction force decreased with increasing porosity, leading to an increase in adsorption capacity and swelling ratio. Experimental data of the adsorption process showed the Freundlich isotherm model. The equilibrium for adsorption and swelling kinetics studies showed and fitted a pseudo-second-order model. NaOH was successful as a desorbing agent with 93.8%, and it followed the pseudo-second-order kinetics model. The recycling process indicates great potential for AR88 removal.
To address Cu(II) and Cr(VI) water pollution, a carbonized zeolite/chitosan (C-ZLCH) composite adsorbent was produced via pyrolysis at 500 °C for two hours. C-ZLCH was characterized using scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), Fourier transform infrared spectroscopy (FTIR), dynamic light scattering (DLS), and zeta potential measurements. The batch experiments were performed by varying the initial pH, concentration, and contact time. The optimal pH values for Cu(II) and Cr(VI) were 8.1 and 9.6, respectively. The highest adsorption capacities for Cu(II) and Cr(VI) were 111.35 mg/g at 60 min and 104.75 mg/g at 90 min, respectively. The effects of chemicals such as sodium (Na+), glucose, ammonium (NH4+), and acid red 88 (AR88) were also studied. Statistical analysis showed that sodium had no significant effect on Cu(II) removal, in contrast to Cr(VI) removal. However, there was a significant effect of the presence of glucose, ammonium, and AR88 on both Cu(II) and Cr(VI) removal. The adsorption isotherm and kinetic models were fitted using Langmuir and pseudo-second-order models for Cu(II) and Cr(VI), respectively.
Phosphate (PO43−) is an essential nutrient in agriculture; however, it is hazardous to the environment if discharged in excess as in wastewater discharge and runoff from agriculture. Moreover, the stability of chitosan under acidic conditions remains a concern. To address these problems, CS-ZL/ZrO/Fe3O4 was synthesized using a crosslinking method as a novel adsorbent for the removal of phosphate (PO43−) from water and to increase the stability of chitosan. The response surface methodology (RSM) with a Box–Behnken design (BBD)-based analysis of variance (ANOVA) was implemented. The ANOVA results clearly showed that the adsorption of PO43− onto CS-ZL/ZrO/Fe3O4 was significant (p ≤ 0.05), with good mechanical stability. pH, dosage, and time were the three most important factors for the removal of PO43−. Freundlich isotherm and pseudo-second-order kinetic models generated the best equivalents for PO43− adsorption. The presence of coexisting ions for PO43− removal was also studied. The results indicated no significant effect on PO43− removal (p ≤ 0.05). After adsorption, PO43− was easily released by 1 M NaOH, reaching 95.77% and exhibiting a good capability over three cycles. Thus, this concept is effective for increasing the stability of chitosan and is an alternative adsorbent for the removal of PO43− from water.
Developing innovative technology for removing methylene blue (MB) from water is essential since the widespread discharge of MB from industrial effluents causes problems for humans and the environment. In this study, we conducted the adsorption method, a simple technique that utilizes an adsorbent. Chitosan is cross-linked with zeolite as a promising adsorbent material and environmentally friendly. For the characterization, FTIR, SEM-EDS, DLS, and pHzpc were analyzed. It was discovered that the removal percentage reached 97% with an adsorption capacity of 242.51 mg/g for 60 minutes at pH 10. The adsorption isotherm and kinetic model were investigated. As a result, the Freundlich model and pseudo-second-order model were fitted to the adsorption process. Moreover, the effect of other ions was investigated for 5 minutes of mixing time. The results showed that the removal percentage increased in the presence of H2O2 ion. Contrary to sodium chloride, glucose, and citric acid ions, the effectiveness of H2SO4 as a desorbing agent was 99.65% for 30 minutes at 45°C.
Glyphosate is an herbicide that is usually used by farmers and is considered harmful to the environment in excess amounts. To address these issues, coffee-husk-biochar-loaded Fe3O4 (CHB- Fe3O4) was used as an adsorbent to remove glyphosate from water. CHB-Fe3O4 characteristics such as pHpzc, FTIR, and SEM were measured to understand the properties of this adsorbent. The best conditions for glyphosate removal by CHB-Fe3O4 were obtained at pH 2.0, where the adsorption capacity and percentage removal are 22.44 mg/g and 99.64%, respectively, after 4 h of adsorption. The Freundlich model provided the best fit for the adsorption isotherm, demonstrating multilayer sorption. The most effective model for characterizing the adsorption kinetics was the pseudo-second-order model with a chemical adsorption mechanism. The desorption studies found that the use of 0.1 M NaOH was the best concentration to effectively desorb glyphosate with a desorption percentage of 69.4%. This indicates that CHB- Fe3O4 is a feasible adsorbent for glyphosate removal from water.
In the present study, alkaline-treated zeolite/chitosan/Fe3+ (ZLCH-Fe) composites were prepared and analyzed using scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR) and pH of zero point of charge (pHzpc) to remove nitrates from water. The process was carried out using an adsorption method with a varied initial pH, adsorbent dosage, initial nitrate concentration and contact time. The pHzpc demonstrated that the ZLCH-Fe surface had a positive charge between 2 and 10, making it easier to capture the negative charge of nitrate. However, the optimal pH value is 7. After 270 min, the maximum adsorption capacity and percent removal reached 498 mg/g and 99.64%, respectively. Freundlich and pseudo-second-order were fitted to the adsorption isotherm and kinetic models, respectively. An evaluation was conducted on the effects of anions—SO42− and PO43−—and dyes—methylene blue (MB) and acid red 88 (AR88)—upon nitrate removal. The results indicated that the effect of the anion could be inhibited, in contrast to dye effects. However, the optimal pH values were changed to 10 for MB and 2 for AR88, resulting in a hydrogel formation. This might be indicated by the protonation of hydroxyl and amino groups resulting from a chitosan nitrate reaction in the AR88 solution.