Catalytic conversion of ethanol to 1-butanol was studied over MgO–Al2O3 mixed oxide-based catalysts. Relationships between acid-base and catalytic properties and the effect of active metal on the hydrogen transfer reaction steps were investigated. The acid-base properties were studied by temperature-programmed desorption of CO2 and NH3 and by the FT-IR spectroscopic examination of adsorbed pyridine. Dispersion of the metal promoter (Pd, Pt, Ru, Ni) was determined by CO pulse chemisorption. The ethanol coupling reaction was studied using a flow-through microreactor system, He or H2 carrier gas, WHSV = 1 , at 21 bar, and 200–350 °C. Formation and transformation of surface species under catalytic conditions were studied by DRIFT spectroscopy. The highest butanol selectivity and yield was observed when the MgO–Al2O3 catalyst contained a relatively high amount of strong-base and medium-strong Lewis acid sites. The presence of metal improved the activity both in He and H2; however, the butanol selectivity significantly decreased at temperatures ≥ 300 °C due to acceleration of undesired side reactions. DRIFT spectroscopic results showed that the active metal promoted H-transfer from H2 over the narrow temperature range of 200–250 °C, where the equilibrium allowed significant concentrations of both dehydrogenated and hydrogenated products.
Ethanol upgrading via catalytic C–C coupling, commonly known as the Guerbet reaction, offers a sustainable route to produce 1-butanol, a high-performance biofuel. To address gaps in the mechanistic understanding of the catalytic reaction, we investigated the process involving a fixed-bed reactor, operated at 275–325 °C, 21 bar, and weight hourly space velocities of 0.25–2.5 gEtOH/(gcat·h), using helium as a carrier gas, with a 5:1 He/EtOH molar ratio. The catalyst was a MgO–Al2O3 mixed oxide (Mg/Al = 2:1), derived from a hydrotalcite precursor. A detailed kinetic model was developed, encompassing 15 species and 27 reversible steps (10 sorption and 17 reaction steps), within a 1+1D sorption–reaction–transport framework. Four C4-forming pathways were included: aldol condensation to form crotonaldehyde, semi-direct coupling to form butyraldehyde and crotyl alcohol, and direct coupling to form 1-butanol. To avoid overfitting, Arrhenius parameters were grouped by reaction type, resulting in sixty rate parameters and one active site-specific density parameter. The optimized model achieved high accuracy, with an average prediction error of 1.44 times the experimental standard deviation. The mechanistic analysis revealed aldol condensation as the dominant pathway below 335 °C, with semi-direct coupling to crotyl alcohol prevailing above 340 °C. The resulting model provides a robust framework for understanding and predicting complex reaction networks in ethanol upgrading systems.
Catalytic upgrading of bioethanol via a C–C coupling reaction is a sustainable method of producing 1-butanol, a high-performance biofuel. This reaction was studied using a flow-through microreactor system with Pd/MgO-Al2O3 and bimetallic Pd-Cu/MgO-Al2O3 mixed oxide-based catalysts in a H2 carrier gas at a pressure of 21 bar and temperatures ranging from 200 to 350 °C. The effect of the metal promoter(s) on the hydrogen transfer reaction steps in the overall reaction was investigated. The palladium promoter significantly improved the activity and butanol selectivity across the entire temperature range. However, the yield of liquid products decreased significantly at temperatures higher than 250 °C, primarily because the decarbonylation side reaction of the acetaldehyde intermediate accelerated. The promoting effect of Pd was most beneficial below 250 °C because the decarbonylation reaction was inhibited by the reversible poisoning effect of CO on multiple Pd sites responsible for decarbonylation. Diluting the Pd phase with Cu increased liquid yields due to gradually decreasing decarbonylation activity. However, the dehydrogenation–hydrogenation activity decreased as well, as did the promoting effect on the corresponding reaction steps in the coupling reaction. Additionally, the product distribution changed dramatically, decreasing 1-butanol selectivity, because metallic Cu can catalyze the formation of ethyl acetate and ketone products.