Weiyi Kong

Dr. Weiyi Kong


Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 April 2026 in Polymers
Verified
Journal Article
Open access
PDF file
Alexey BeskopylnyAlexey Beskopylny
Alexey Beskopylny
Sergey A. Stel'makhSergey A. Stel'makh
Sergey A. Stel'makh
Evgenii M. Shcherban'Evgenii M. Shcherban'
Evgenii M. Shcherban'
DEDiana Elshaeva
Diana Elshaeva
Andrei Chernil'nikAndrei Chernil'nik
Andrei Chernil'nik
WKWeiyi Kong
Weiyi Kong
Modern construction extensively utilizes foam concrete (FC) because of its distinct characteristics. However, its application is limited by its low strength properties. Developing high-strength FC by strengthening the matrix with various additives and incorporating various types of fibers into the composition is one of the most rational trends, consistent with the concept of sustainable and environmentally friendly construction. This study explores the impact of diverse polymer fibers on the strength and deformation characteristics of fiber-reinforced foam concrete (FRFC). The concrete’s matrix is strengthened by a composite nanomodifying additive. A FEM model was developed, and experimental studies of the compressive and flexural strength of FRFC were conducted. In the numerical study, the FC matrix is described by the Menetrey-Willam model. Parameter calibration and model verification demonstrated good agreement with experimental data. Experiments and numerical simulations proved that polypropylene fibers enhance compressive strength by as much as 20% and flexural strength by 80%. The stress–strain condition of FRFC was numerically analyzed, considering the influence of steel, carbon, and glass fibers. It was shown that high-modulus polymer fibers quickly lose their adhesive properties and impair the deformation properties of the composite compared to polypropylene fibers.

17 July 2025 in Materials
Verified
Journal Article
Open access
PDF file
DSDunlei Su
Dunlei Su
MYMingxin Yang
Mingxin Yang
YHYani Hao
Yani Hao
JWJiahui Wang
Jiahui Wang
XLXIN LIU
XIN LIU
WKWeiyi Kong
Weiyi Kong
In order to elucidate the high-temperature reaction process of solid waste-based high belite sulphoaluminate cement containing residual gypsum in clinker (NHBSAC) and obtain the formation laws of each mineral in clinker, this article studied its high-temperature reaction kinetics. Through QXRD analysis and numerical fitting methods, the formation of C4A3S¯, β-C2S, and CaSO4 in clinker under different calcination systems was quantitatively characterized, the corresponding high-temperature reaction kinetics models were established, and the reaction activation energies of each mineral were obtained. The results indicate that the content of C4A3S¯ and β-C2S increases with the prolongation of holding time and the increase in calcination temperature, while CaSO4 is continuously consumed. Under the control mechanism of solid-state reaction, the formation and consumption of minerals follow the kinetic equation. C4A3S¯ and β-C2S satisfy the D4 equation under diffusion mechanism control, and CaSO4 satisfies the R3 equation under interface chemical reaction mechanism control. The activation energy required for mineral formation varies with different temperature ranges. The activation energies required to form C4A3S¯ at 1200–1225 °C, 1225–1275 °C, and 1275–1300 °C are 166.28 kJ/mol, 83.14 kJ/mol, and 36.58 kJ/mol, respectively. The activation energies required to form β-C2S at 1200–1225 °C and 1225–1300 °C are 374.13 kJ/mol and 66.51 kJ/mol, respectively. This study is beneficial for achieving flexible control of the mineral composition of NHBSAC clinker, providing a theoretical basis and practical experience for the preparation of low-carbon cement and the optimization design of its mineral composition.

30 June 2025 in Coatings
Verified
Journal Article
Open access
PDF file
DSDunlei Su
Dunlei Su
XLXIN LIU
XIN LIU
HTHaojian Tang
Haojian Tang
YHYani Hao
Yani Hao
JWJiahui Wang
Jiahui Wang
WKWeiyi Kong
Weiyi Kong
Based on a novel ternesite sulphoaluminate cement (NTSAC), the effects of various influencing factors on the calcination of clinker were studied, including mineral composition of clinker, grinding fineness of raw materials, molding technology of samples, and cooling methods of clinker. The research was carried out by taking the calcination system and mineral content of clinker as evaluation indexes, and using RSM and QXRD as analytical means. The results indicate that the optimal calcination temperature of clinker varies with the design mineral composition, while the holding time remains basically unchanged. Clinker with high CaSO4 content has a relatively lower calcination temperature. The use of a calcination system of 1175 °C-49 min can control the mineral content error of the cement below 15%. Moreover, the molding pressure, molding methods, grinding fineness of raw materials, and cooling methods of clinker have significant effects on the clinker preparation to varying degrees, with the order of influence from high to low being molding methods, grinding fineness of raw materials, molding pressure, and cooling methods of clinker. Within the range of experimental parameters, the better preparation conditions are compression molding (molding method), 15 MPa (molding pressure), and 20 μm (grinding fineness). The above research conclusions provide reference data for cement preparation in the laboratory, offering useful guidance for developing novel types of cement.