The room-temperature continuous-wave operation of a 1.5λ-cavity GaN-based vertical-cavity surface-emitting laser with an n-type conducting AlInN/GaN distributed Bragg reflector (DBR) was achieved. A peak reflectivity of over 99.9% was obtained in the n-type conducting AlInN/GaN DBR so that the current was injected through the DBR for the operation. The threshold current was 2.6 mA, corresponding to the threshold current density of 5.2 kA/cm2, and the operating voltage was 4.7 V. A lasing spectrum with a peak wavelength of 405.1 nm and a full-width at half maximum of 0.08 nm was also observed.
This paper describes the status and prospects of gallium nitride-based vertical-cavity surface-emitting lasers (VCSELs) with semiconductor-based distributed Bragg reflectors. These optoelectronic devices, which emit laser light from the violet to green region, are expected to be a superior light source for the next-generation of displays and illumination, such as retinal scanning displays and adaptive headlights. The development status and prospects are discussed in comparison with already commercialized gallium arsenide-based infrared VCSELs.
In this paper, room‐temperature continuous‐wave operation of a GaN‐based vertical‐cavity surface‐emitting laser (VCSEL) with a convex structure for optical guiding is demonstrated. The GaN‐based VCSEL is designed and fabricated with the convex structure containing a 15‐nm step between the center area and the peripheral area of the VCSEL with a Nb2O5 spacer layer. In theory the convex structure with a 1.5% relative refractive index difference between the areas could provide more than 10 high‐order modes. Experimental emission spectra and near field pattern images clearly suggested a multi‐mode operation of the VCSEL with the convex structure. In addition, the VCSEL shows a lower threshold current, 2 mA, and a higher maximum light output power, 0.88 mW, which are superior to those of our standard VCSEL fabricated simultaneously without the convex structure. These results indicate that the optical guiding with the convex structure plays an important role in developments of GaN‐based VCSELs.
We have systematically investigated acceptor (Mg) and donor (Si) profiles at GaN tunnel junction interfaces with the aim of a low resistivity under reverse bias. We found that an overlap between Mg and Si at the tunnel junction interface was effective to obtain a lower resistivity of the GaN tunnel junctions, which contradicts the typical picture of conventional semiconductor-based tunnel junctions. We demonstrated a light-emitting diode with the GaN tunnel junction prepared in a single growth run by metalorganic vapor phase epitaxy, showing a differential resistivity of 2.4×10-4 Ωcm2 at 5 kA/cm2.
23 May 2019 in Japanese Journal of Applied Physics
We investigated the etching rate of the m-plane of AlGaN by wet etching with tetramethylammonium hydroxide aqueous solutions (25 wt%, 85 °C). After dry etching was performed along the m-plane of AlGaN, wet etching was performed to stably form the m-plane facet of AlGaN. Also, the etching rate increases as the increased AlN molar fraction. In the case of forming a heterojunction such as a UV light-emitting diode, by performing wet etching for 5 min, the flat m-plane facets were formed even though there was a large dependence in AlN molar fraction. These facets were almost vertical and flat with respect to the c-plane, so it has the potential for the use as laser mirror. Also, no change in current density–voltage characteristics was confirmed after the wet etching. Therefore, this method is effective for deep UV laser diode fabrication technology on sapphire substrate.
We demonstrated low-resistivity GaInN-based tunnel junctions using graded GaInN layers. A systematic investigation of the samples grown by metalorganic vapor phase epitaxy revealed that a tunnel junction consisting of a 4 nm both-sides graded GaInN layer (Mg: 1 × 1020 cm−3) and a 2 nm GaN layer (Si: 7 × 1020 cm−3) showed the lowest specific series resistance of 2.3 × 10−4 Ω cm2 at 3 kA/cm2 in our experiment. The InN mole fraction in the 4 nm both-sides graded GaInN layer was changed from 0 through 0.4 to 0. The obtained resistance is comparable to those of standard p-contacts with Ni/Au and MBE-grown tunnel junctions.