Pengkun Quan

Dr. Pengkun Quan

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 June 2021 in IEEE Access
Verified
Journal Article
Open access
PQPengkun Quan
Pengkun Quan
YLYa'nan Lou
Ya'nan Lou
HLHaoyu Lin
Haoyu Lin
ZLZhuo Liang
Zhuo Liang
SDShichun Di
Shichun Di
The maturity of automatic driving and parking technologies is gradually driving electric vehicle charging toward automation. The primary condition of automatic charging that has a high significance is the identification of electric vehicle charging ports. This research proposes an automatic system for the identification and positioning of charging ports of electric vehicles. The system is mainly divided into rough and precise positioning. The former is based on the Hough circle and the Hough line, and locates the position information of the charging port. The latter uses the Canny operator to obtain the contour information of the original and gradient images respectively. All the contours of the two images are fitted into ellipses by the quadratic curve standardization (QCS) method, and irrelevant ellipses are screened out. Finally, the perspective-n-point (PNP) algorithm is used to locate the pose information of the charging port. The aubo-i10 6-DOF articulated robot is used to test the recognition and insertion accuracies in different environments. The results show that the average recognition rate of rough positioning is 97.9%, the average displacement error of precise positioning in X, Y and Z directions are 0.60, 0.83 and 1.23 mm, respectively, and the average angle errors in RX, RY and RZ directions are 1.19, 0.97 and 0.50 degrees, respectively. The average success rate is 94.8%. These results demonstrate that the proposed system meets the basic plug-in requirements of electric vehicle charging ports.

9 May 2022 in Sensors
Verified
Journal Article
Open access
PDF file
PQPengkun Quan
Pengkun Quan
YLYa'nan Lou
Ya'nan Lou
HLHaoyu Lin
Haoyu Lin
ZLZhuo Liang
Zhuo Liang
DWDongbo Wei
Dongbo Wei
SDShichun Di
Shichun Di
With the gradual maturity of driverless and automatic parking technologies, electric vehicle charging has been gradually developing in the direction of automation. However, the pose calculation of the charging port (CP) is an important part of realizing automatic charging, and it represents a problem that needs to be solved urgently. To address this problem, this paper proposes a set of efficient and accurate methods for determining the pose of an electric vehicle CP, which mainly includes the search and aiming phases. In the search phase, the feature circle algorithm is used to fit the ellipse information to obtain the pixel coordinates of the feature point. In the aiming phase, contour matching and logarithmic evaluation indicators are used in the cluster template matching algorithm (CTMA) proposed in this paper to obtain the matching position. Based on the image deformation rate and zoom rates, a matching template is established to realize the fast and accurate matching of textureless circular features and complex light fields. The EPnP algorithm is employed to obtain the pose information, and an AUBO-i5 robot is used to complete the charging gun insertion. The results show that the average CP positioning errors (x, y, z, Rx, Ry, and Rz) of the proposed algorithm are 0.65 mm, 0.84 mm, 1.24 mm, 1.11 degrees, 0.95 degrees, and 0.55 degrees. Further, the efficiency of the positioning method is improved by 510.4% and the comprehensive plug-in success rate is 95%. Therefore, the proposed CTMA in this paper can efficiently and accurately identify the CP while meeting the actual plug-in requirements.

14 April 2023 in Electronics
Verified
Journal Article
Open access
PDF file
PQPengkun Quan
Pengkun Quan
YLYa'nan Lou
Ya'nan Lou
HLHaoyu Lin
Haoyu Lin
ZLZhuo Liang
Zhuo Liang
DWDongbo Wei
Dongbo Wei
SDShichun Di
Shichun Di
With the gradual maturity of autonomous driving and automatic parking technology, electric vehicle charging is moving towards automation. The charging port (CP) location is an important basis for realizing automatic charging. Existing CP identification algorithms are only suitable for a single vehicle model with poor universality. Therefore, this paper proposes a set of methods that can identify the CPs of various vehicle types. The recognition process is divided into a rough positioning stage (RPS) and a precise positioning stage (PPS). In this study, the data sets corresponding to four types of vehicle CPs under different environments are established. In the RPS, the characteristic information of the CP is obtained based on the combination of convolutional block attention module (CBAM) and YOLOV7-tinp, and its position information is calculated using the similar projection relationship. For the PPS, this paper proposes a data enhancement method based on similar feature location to determine the label category (SFLDLC). The CBAM-YOLOV7-tinp is used to identify the feature location information, and the cluster template matching algorithm (CTMA) is used to obtain the accurate feature location and tag type, and the EPnP algorithm is used to calculate the location and posture (LP) information. The results of the LP solution are used to provide the position coordinates of the CP relative to the robot base. Finally, the AUBO-i10 robot is used to complete the experimental test. The corresponding results show that the average positioning errors (x, y, z, rx, ry, and rz) of the CP are 0.64 mm, 0.88 mm, 1.24 mm, 1.19 degrees, 1.00 degrees, and 0.57 degrees, respectively, and the integrated insertion success rate is 94.25%. Therefore, the algorithm proposed in this paper can efficiently and accurately identify and locate various types of CP and meet the actual plugging requirements.

25 February 2021 in Sensors
Verified
Journal Article
Open access
PDF file
YLYa'nan Lou
Ya'nan Lou
HLHaoyu Lin
Haoyu Lin
PQPengkun Quan
Pengkun Quan
DWDongbo Wei
Dongbo Wei
SDShichun Di
Shichun Di
The structure of the cable-driven serial manipulator (CDSM) is more complex than that of the cable-driven parallel manipulator (CDPM), resulting in higher model complexity and stronger structural and parametric uncertainties. These drawbacks challenge the stable trajectory-tracking control of a CDSM. To circumvent these drawbacks, this paper proposes a robust adaptive controller for an n-degree-of-freedom (DOF) CDSM actuated by m cables. First, two high-level controllers are designed to track the joint trajectory under two scenarios, namely known and unknown upper bounds of uncertainties. The controllers include an adaptive feedforward term based on inverse dynamics and a robust control term compensating for the uncertainties. Second, the independence of control gains from the upper bound of uncertainties and the inclusion of the joint viscous friction coefficient into the dynamic parameter vector are realised. Then, a low-level controller is designed for the task of tracking the cable tension trajectory. The system stability is analysed using the Lyapunov method. Finally, the validity and effectiveness of the proposed controllers are verified by experimenting with a three-DOF six-cable CDSM. In addition, a comparative experiment with the classical proportional–integral–derivative (PID) controller is carried out.

30 April 2022 in Sensors
Verified
Journal Article
Open access
PDF file
HLHaoyu Lin
Haoyu Lin
PQPengkun Quan
Pengkun Quan
ZLZhuo Liang
Zhuo Liang
YLYa'nan Lou
Ya'nan Lou
DWDongbo Wei
Dongbo Wei
SDShichun Di
Shichun Di
With the increasing popularity of electric vehicles, cable-driven serial manipulators have been applied in auto-charging processes for electric vehicles. To ensure the safety of the physical vehicle–robot interaction in this scenario, this paper presents a model-independent collision localization and classification method for cable-driven serial manipulators. First, based on the dynamic characteristics of the manipulator, data sets of terminal collision are constructed. In contrast to utilizing signals based on torque sensors, our data sets comprise the vibration signals of a specific compensator. Then, the collected data sets are applied to construct and train our collision localization and classification model, which consists of a double-layer CNN and an SVM. Compared to previous works, the proposed method can extract features without manual intervention and can deal with collision when the contact surface is irregular. Furthermore, the proposed method is able to generate the location and classification of the collision at the same time. The simulated experiment results show the validity of the proposed collision localization and classification method, with promising prediction accuracy.

28 December 2023 in IEEE/ASME Transactions on Mechatronics
Verified
Journal Article
Closed access
ZLZhuo Liang
Zhuo Liang
BJBo Jiang
Bo Jiang
PQPengkun Quan
Pengkun Quan
HLHaoyu Lin
Haoyu Lin
YLYa'nan Lou
Ya'nan Lou
SDShichun Di
Shichun Di
Multilink cable-driven redundant manipulators (MCDRMs) offer numerous advantages over conventional manipulators, making them well suited for operation in narrow and confined environments. However, MCDRMs face limitations in terms of cable quantity and cable routing scheme, which are crucial for achieving full constraint. Force closure, a crucial parameter for evaluating the performance of MCDRMs, ensures that the manipulator can exert sufficient force and torque to stably perform tasks within its workspace. In this article, we propose a novel force-closure analysis method for MCDRMs that considers both cable coupling and friction effects. First, we utilize the Euler–Eytelwein equation to analyze the effect of friction between cables and cable routing holes on the tension of different cable subsegments. Then, utilizing the reciprocal screw theory, we elucidate the cable coupling in MCDRMs and calculate the active joint torques provided by the cable tension, as well as passive joint torques generated by external wrenches. Furthermore, we analyze the force closure of the MCDRM by balancing the passive and active joint torques. Finally, simulations and experiments are conducted using a planar MCDRM. The results demonstrate that the proposed method enables systematic and accurate analysis of the force closure of MCDRDs with arbitrary cable routing schemes.